manualshive.com logo in svg

Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03, Technical Manual

The Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03 is a high-performance device designed for various applications. To unleash its full potential, make sure to download the comprehensive Technical Manual. This manual is available for free download from manualshive.com, providing essential information to maximize your experience with this versatile product.

Share
Download
background image

III PERIPHERAL BLOCK: 8-BIT PROGRAMMABLE TIMERS

S1C33L03 FUNCTION PART

EPSON

B-III-3-13

A-1

B-III

8TM

CFP13–CFP10: P1[3:0] pin function selection (D[3:0]) / P1 function select register (0x402D4)

Selects the pin that is used to output a timer underflow signal to external devices.

Write "1": Underflow signal output pin

Write "0": I/O port pin

Read: Valid

Select the pin used to output a timer underflow signal to external devices from among P10 through P13 by writing

"1" to the corresponding bit, CFP10 through CFP13. P10 through P13 correspond to timers 0 through 3,

respectively. If "0" is written to CFP1x, the pin is set for an I/O port.

At cold start, CFP1x is set to "0" (I/O port). At hot start, the bit retains its state from prior to the initial reset.

IOC13–IOC10: P1[3:0] port I/O control (D[3:0]) / P1 I/O control register (0x402D6)

Directs P10 through P13 for input or output and indicates the I/O control signal value of the port.

When writing data

Write "1": Output mode

Write "0": Input mode

If a pin chosen from among P10 through P13 is used to output an underflow signal, write "1" to the corresponding

I/O control bit to set it to output mode. If the pin is set to input mode, even if its CFP1x is set to "1", it functions as

the event counter input pin of a 16-bit programmable timer cannot be used to output a timer underflow signal.

When reading data

Read "1": I/O control signal (output)

Read "0": I/O control signal (input)

The I/O control signal value for the port pin is read from this register. When I/O port function is selected using the

CFEX and CFP1x registers, the value written to the IOC register is read out as is. When peripheral function is

selected, the read value depends on the peripheral circuit status and may not indicate the value written to the IOC

register.

At cold start, IOC1x is set to "0" (input mode). At hot start, the bit retains its state from prior to the initial reset.

CFEX1: P10, P11, P13 port extended function (D1) / Port function extension register (0x402DF)
CFEX0: P12, P14 port extended function (D0) / Port function extension register (0x402DF)

Sets whether the function of an I/O-port pin is to be extended.

Write "1": Function-extended pin

Write "0": I/O-port/peripheral-circuit pin

Read: Valid

When CFEX[1:0] is set to "1", the P13–P10 ports function as debug signal output ports. When CFEX[1:0] = "0",

the CFP1[3:0] bit becomes effective, so the settings of these bits determine whether the P13–P10 ports function as

I/O port s or timer underflow signal output ports.

At cold start, CFEX[1:0] is set to "1" (function-extended pins). At hot start, CFEX[1:0] retains its state from prior

to the initial reset.

RLD07–RLD00: Timer 0 reload data (D[7:0]) / 8-bit timer 0 reload data register (0x40161)
RLD17–RLD10: Timer 1 reload data (D[7:0]) / 8-bit timer 1 reload data register (0x40165)
RLD27–RLD20: Timer 2 reload data (D[7:0]) / 8-bit timer 2 reload data register (0x40169)
RLD37–RLD30: Timer 3 reload data (D[7:0]) / 8-bit timer 3 reload data register (0x4016D)
RLD47–RLD40: Timer 4 reload data (D[7:0]) / 8-bit timer 4 reload data register (0x40175)
RLD57–RLD50: Timer 5 reload data (D[7:0]) / 8-bit timer 5 reload data register (0x40179)

Set the initial counter value of each timer.

The reload data set in this register is loaded into each counter, and the counter starts counting down beginning with

this data, which is used as the initial count.

There are two cases in which the reload data is loaded into the counter: when data is preset after "1" is written to

PSETx, or when data is automatically reloaded upon counter underflow.

At initial reset, RLD is not initialized.

Summary of Contents for CMOS 32-Bit Single Chip Microcomputer S1C33L03
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CMOS 32-Bit Single Chip Microcomputer S1C33L03

Roland MSL-15 Owner'S Manual preview
MSL-15
Brand: Roland Pages: 12
Qlogic QMC2462S Datasheet preview
QMC2462S
Brand: Qlogic Pages: 2
Telit Wireless Solutions HE922-3GR Hardware User'S Manual preview
HE922-3GR
Brand: Telit Wireless Solutions Pages: 113
Nvidia DGX A100 User Manual preview
DGX A100
Brand: Nvidia Pages: 115
VCS VideoJet 100 Manual preview
VideoJet 100
Brand: VCS Pages: 118
Arduino ABX00061 Reference Manual preview
ABX00061
Brand: Arduino Pages: 25
Divio SRA311-008P8 Series Installation Manual preview
SRA311-008P8 Series
Brand: Divio Pages: 4
Isee IGEPv2 BOARD Hardware Reference Manual preview
IGEPv2 BOARD
Brand: Isee Pages: 68
ATI Technologies RADEON 9800 PRO Getting Started Manual preview
RADEON 9800 PRO
Brand: ATI Technologies Pages: 20
Lattice Semiconductor sysCLOCK ECP5 Usage Manual preview
sysCLOCK ECP5
Brand: Lattice Semiconductor Pages: 43
Paradyne ACCULINK 3161 CSU Quick Reference Manual preview
ACCULINK 3161 CSU
Brand: Paradyne Pages: 19
ivideon Bridge B1610 Quick Start Manual preview
Bridge B1610
Brand: ivideon Pages: 11
LaCie FireWire 800 ExpressCard 34 Quick Install Manual preview
FireWire 800 ExpressCard 34
Brand: LaCie Pages: 24
AXIOMTEK FAB118-14B5P7 Quick Installation Manual preview
FAB118-14B5P7
Brand: AXIOMTEK Pages: 2
Cypress Semiconductor CY7C1381DV25 Specification Sheet preview
CY7C1381DV25
Brand: Cypress Semiconductor Pages: 28
VIA Technologies LPC-01 Quick Manual preview
LPC-01
Brand: VIA Technologies Pages: 2
Multitech MultiModem ISIHP-2S User Manual preview
MultiModem ISIHP-2S
Brand: Multitech Pages: 155
Avaya VSP 8284XSQ-AC Quick Install Manual preview
VSP 8284XSQ-AC
Brand: Avaya Pages: 2

Brands by name

Popular brands

Load more brands