manualshive.com logo in svg

Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03, Technical Manual

The Epson CMOS 32-Bit Single Chip Microcomputer S1C33L03 is a high-performance device designed for various applications. To unleash its full potential, make sure to download the comprehensive Technical Manual. This manual is available for free download from manualshive.com, providing essential information to maximize your experience with this versatile product.

Share
Download
background image

V DMA BLOCK: IDMA (Intelligent DMA)

S1C33L03 FUNCTION PART

EPSON

B-V-3-1

A-1

B-V

IDMA

V-3

 

IDMA (Intelligent DMA)

Functional Outline of IDMA

The DMA Block contains an intelligent DMA (IDMA), a function that allows control information to be

programmed in RAM. Up to 128 channels can be programmed, including 31 channels that are invoked by an

interrupt factor that occurs in some internal peripheral circuit.

Although an additional overhead for loading and storing control information in RAM may be incurred, this

intelligent DMA supports such functions as successive transfers, block transfers, and linking to another IDMA.

IDMA is invoked by an interrupt factor that occurs in some internal peripheral circuit or a software trigger, thereby

performing a data transfer according to the control information in RAM. When the transfer is completed, IDMA

can generate an interrupt or invoke another IDMA according to link settings.

Programming Control Information

The intelligent DMA operates according to the control information prepared in RAM. The control information can

be stored in either internal RAM or external RAM should the necessary area be allocated.

The control information is 3 words (12 bytes) per channel in size, and must be located at contiguous addresses

beginning with the base address that is set in the software application as the starting address of channel 0.

Consequently, an area of 384 words (1,536 bytes) in RAM is required in order for all of 128 channels to be used.

The following explains how to set the base address and the contents of control information. Before using IDMA,

make each the settings described below.

Setting the base address

Set the starting address of control information (starting address of channel 0) in the IDMA base address

register.

16 low-order bits: DBASEL[15:0] (D[F:0]) / IDMA base address low-order register (0x48200)

12 high-order bits: DBASEH[11:0] (D[B:0]) / IDMA base address high-order register (0x48202)

When initially reset, the base address is set to 0x0C003A0.

Notes: • The address you set in the IDMA base address register must always be a word (32-bit)

boundary address.

• Be  sure  to  disable DMA transfers (IDMAEN = "0") before setting the base address. Writing to the

IDMA base address register is ignored when the DMA transfer is enabled (IDMAEN = "1").
When the register is read, the read data is indeterminate.

Control information

Write the control information for the IDMA channels used to RAM.

The addresses at which the control information of each channel is placed are determined by the base address

and a channel number.

Starting address of channel = base a (channel number 

×

 12 [bytes])

Note: The  control  information must be written only when the channel to be set does not start a DMA

transfer. If a DMA transfer starts when the control information is being written to the RAM, proper
transfer cannot performed. Reading the control information can always be done.

Summary of Contents for CMOS 32-Bit Single Chip Microcomputer S1C33L03
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CMOS 32-Bit Single Chip Microcomputer S1C33L03

D-Link PCMCIA WIRELESS ASAPTER DWL-650 Quick Install Manual preview
PCMCIA WIRELESS ASAPTER DWL-650
Brand: D-Link Pages: 5
D-Link PowerLine DHP-W611AV User Manual preview
PowerLine DHP-W611AV
Brand: D-Link Pages: 78
IBA Com-L2B-4-8 Manual preview
Com-L2B-4-8
Brand: IBA Pages: 29
Behringer EXPANSION CARD X-DANTE Quick Start Manual preview
EXPANSION CARD X-DANTE
Brand: Behringer Pages: 65
Renesas Compact Emulator M30620T-CPE User Manual preview
Compact Emulator M30620T-CPE
Brand: Renesas Pages: 52
Supermicro SuperServer 5019S-L User Manual preview
SuperServer 5019S-L
Brand: Supermicro Pages: 61
Time domain PulsON 440 Datasheet And User Manual preview
PulsON 440
Brand: Time domain Pages: 64
Internet Security Systems Proventia A1204 User Manual preview
Proventia A1204
Brand: Internet Security Systems Pages: 42
Velopex Extra-X Quick Start Manual preview
Extra-X
Brand: Velopex Pages: 7
Tandberg Data SUPERLOADER DLT MAGAZINE Quick Start Manual preview
SUPERLOADER DLT MAGAZINE
Brand: Tandberg Data Pages: 6
C&H Active Module Carrier VX402C-64 User Manual preview
Active Module Carrier VX402C-64
Brand: C&H Pages: 32
H3C NSQ1GT48EA0 Manual preview
NSQ1GT48EA0
Brand: H3C Pages: 3
Aaeon SBC-657B Manual preview
SBC-657B
Brand: Aaeon Pages: 61
Magewell XI100DUSB-SDI User Manual preview
XI100DUSB-SDI
Brand: Magewell Pages: 10
Z3 Technology Z3-HE2160-RPS User Instructions preview
Z3-HE2160-RPS
Brand: Z3 Technology Pages: 18
Keithley 7075 Instruction Manual preview
7075
Brand: Keithley Pages: 108
Ciara Horizon D10750 Disassembly Manual preview
Horizon D10750
Brand: Ciara Pages: 14
PairGain HiGain Line Unit HLU-388 Quick Installation Manual preview
HiGain Line Unit HLU-388
Brand: PairGain Pages: 7

Brands by name

Popular brands

Load more brands