Configuring Spanning Tree Loop Protect Features
show spantree lp
6-66 Spanning Tree Configuration
Parameters
Defaults
If
no
SID
is
specified,
SID
0
is
assumed.
Mode
Switch
command,
Read
‐
Write.
Usage
The
Loop
Protect
feature
is
disabled
by
default.
See
“Loop
Protect”
on
page 2.
for
more
information.
Loop
Protect
takes
precedence
over
per
port
STP
enable/disable
(portAdmin).
Normally
portAdmin
disabled
would
cause
a
port
to
go
immediately
to
forwarding.
If
Loop
Protect
is
enabled,
that
port
should
go
to
listening
and
remain
there.
Example
This
example
shows
how
to
enable
Loop
Protect
on
fe.2.3:
Matrix(rw)->set spantree lp enable fe.2.3
show spantree lp
Use
this
command
to
display
the
Loop
Protect
status
per
port
and/or
per
SID.
Syntax
show spantree lp
[
port
port-string
] [
sid
sid
]
Parameters
Defaults
If
no
port
‐
string
is
specified,
status
is
displayed
for
all
ports.
port
‐
string
Specifies
port(s)
on
which
to
enable
or
disable
the
Loop
Protect
feature.
For
a
detailed
description
of
possible
port
‐
string
values,
refer
to
“
Port
String
Syntax
Used
in
the
CLI
”
on
page 4
‐
2.
enable
|
disable
Enables
or
disables
the
feature
on
the
specified
port.
sid
sid
(Optional)
Enables
or
disables
the
feature
for
specific
Spanning
Tree(s).
Valid
values
are
0
‐
4094
.
If
not
specified,
SID
0
is
assumed.
Note:
The Loop Protect enable/disable settings for an MSTI port should match those for the CIST
port.
port
‐
string
(Optional)
Specifies
port(s)
for
which
to
display
the
Loop
Protect
feature
status.
For
a
detailed
description
of
possible
port
‐
string
values,
refer
to
“
Port
String
Syntax
Used
in
the
CLI
”
on
page 4
‐
2.
sid
sid
(Optional)
Specifies
the
specific
Spanning
Tree(s)
for
which
to
display
the
Loop
Protect
feature
status.
Valid
values
are
0
‐
4094
.
If
not
specified,
SID
0
is
assumed.
Summary of Contents for Enterasys Matrix DFE-Gold Series
