Emerson DL8000 Instruction Manual Download Page 80

Page: 80 / 330

DL8000 Preset Instruction Manual

3-42

Modules

Revised February-2016

Note

When installing a dial-up modem module, you must remove

power from the DL8000.

The dial-up modem provides communications with speeds up to 14.4K

bps with V.42 bis and V.42, MNP2-4 and MNP10 error correction.
The dial-up modem module is FCC Part 68 approved for use with

PSTNs. The FCC label on the module provides the FCC registration

number and the ringer equivalent. The dial-up modem module supports

data compression, error correction, and nonvolatile RAM for permanent

storage of the modem configuration.
The dial-up modem module interfaces to two-wire, full-duplex

telephone lines using asynchronous operation. The module interfaces to

a PSTN through an RJ-11 jack. The dial-up modem can be controlled

using industry-standard AT command software. A 40-character

command line is provided for the AT command set, which is compatible

with EIA document TR302.2/88-08006.
The dial-up modem automatically hangs up after a configured period of

communications inactivity. The dial-up modem provides automated

dial-up alarm reporting capabilities.

Table 3-18. RJ-11 Field Connections

Signal

Pin

Tip

Ring

LED indicators on the module show the status of the Receive (RX),

Transmit (TX), Ring (RI), and Carrier Detect (CD) control lines.

Table

4-19

displays connector signals and their functions.

Table 3-19. Modem Signal Routing – Comm3, Comm4, and Comm5

Signal

Function

Terminal

Lit when module (Comm3, Comm4, or Comm5) is currently receiving.

Lit when module (Comm3, Comm4, or Comm5) is currently transmitting (Tip).

Lit when module (Comm3, Comm4, or Comm5) on ring (Ring).

Lit when module (Comm3, Comm4, or Comm5) on carrier detect.

Notes



If you are installing a modem module, it is recommended that you

install a surge protector between the RJ-11 jack and the outside line.



The dial-up modem is

not

hot-swappable

hot-pluggable. When

installing a dial-up modem module, you

must

remove power from

the DL8000.

Summary of Contents for DL8000











































































































































































































































































































































Search results

Summary of Contents for DL8000

Reviews:

Related manuals for DL8000

Brands by name

Popular brands

Emerson DL8000, Instruction Manual

Search results

Summary of Contents for DL8000

Reviews:

Related manuals for DL8000

Brands by name

Popular brands