![background image](http://html1.mh-extra.com/html/efka/dc-1500/dc-1500_instruction-manual_2367392038.webp)
EFKA FP220A5911
39
Mode 6
Chainstitch Machines with Tape Cutter or Fast Scissors
-
Signal M1 after stop in position 2 after delay (kd1) during ON period (kt1)
-
Signal M2 after stop in position 2 after delay (kd2) during ON period (kt2)
-
Fast scissors (M3) after delay (kd3) during ON period (kt3) alternating with M4
-
Fast scissors (M4) after delay (kd4) during ON period (kt4) alternating with M3
-
Sewing foot lifting (see chapter "Sewing Foot Lifting")
-
Stitch condensing (see chapter "Start Stitch Condensing" and "End Stitch Condensing")
-
Signal “machine running”
-
Signal “machine at standstill”
Mode 7
Overlock Machines
-
Signal M1 after stop in position 2 after delay (kd1) during ON period (kt1)
-
Signal M2 after stop in position 2 after delay (kd2) during ON period (kt2) or
if parameter 232=1, as
fast scissors
alternating with M3
(parameter 282=0)
-
Chain suction during stitch count (c1) at the start of the seam and stitch counting (c2) at the seam end
-
Thread tension release after light barrier uncovered
-
Tape cutter at the start of the seam after stitch count (c3) and at the seam end after stitch count (c4) and
the delay time (kd3)
-
Sewing foot lifting (see chapter "Sewing Foot Lifting")
-
If parameter 018 = 1, parameter 022 must also be set at "1"
-
Signal “machine running”
-
Signal “machine at standstill”
Mode 8
Backlatch Machines (Pegasus)
-
Signal M1 with pedal in positions -1 and –2
-
Signal M2 with pedal in positions 1-12
-
Inverted signal M3 with pedal in positions 1-12
-
Sewing foot lifting (see chapter "Sewing Foot Lifting")
-
Signal “machine running”
-
Signal “machine at standstill”
-
Operation at automatic speed
-
Automatic speed has priority over machine run blockage
-
Machine run blockage effective with open contact
(input in1 / parameter 240=6)
»Automatic speed has priority over machine run blockage«
-
Key for operation at automatic speed
(input in3 / parameter 242=10)
Mode 9
Backlatch Machines (Yamato)
-
Signal M1 with pedal in positions -1 and –2
-
Signal M2 with pedal in positions 1-12
-
Inverted signal M3 with pedal in positions 1-12
-
Sewing foot lifting (see chapter "Sewing Foot Lifting")
-
Signal “machine running”
-
Signal “machine at standstill”
-
Key for operation at automatic speed
(input in3 / parameter 242=10)
-
Machine run blockage effective with open contact
(input in1 / parameter 240=6)
-
Machine run blockage has priority over automatic speed
Mode 10
Lockstitch Machines (Refrey Trimmer)
-
Thread trimmer from trailing edge of slot position 1 to leading edge of slot position 2
-
Thread trimmer backward after stop in position 2 during ON period (kt1).
-
After that the signal is pulsed.
-
Thread tension release whose signal is parallel to the thread trimmer
-
Thread wiper (M3) after delay (kd3) during ON period (kt3)
-
Sewing foot lifting (see chapter "Sewing Foot Lifting")
-
Backtacking (see chapter "Start Backtack" and "End Backtack")
-
Signal “machine running”
Mode 14
Lockstitch Machines (Juki 5550-6, 5550-7)
-
Thread trimmer (M1) from trailing edge of slot position 1 to leading edge of slot position 2
-
Thread trimmer (M4) from leading edge of slot position 1 to leading edge of slot position 2
-
Thread wiper (M3) for a programmable time (t6)
-
Thread puller (M2) after stop in position 2 after delay (kd2) during ON period (kt2)
-
Sewing foot lifting (see chapter "Sewing Foot Lifting")
-
Backtacking (see chapter "Start Backtack" and "End Backtack")
-
Signal (M5) “machine running”
-
Signal (M6) “machine at standstill”
-
Positioning by Juki handwheel sensor on the control