EFKA FP220A5911
27
7.6 Programming of Seams (TEACH IN)
!
A maximum of 99 patterns with a total of 99 seams can be programmed, i. e. 1 pattern with 99 seams each or 99
patterns with 1 seam each. In between, all combinations are possible.
!
Programming is possible with or without code number.
!
The functions “start backtack”, “end backtack”, “stitch counting”, “light barrier”, “thread trimmer”, “sewing foot lift”
and “needle positions” can be assigned individually to each seam.
!
The functions of signals A1 and A2 can also be assigned to each seam, on condition that slide-in strip 6, 8, 9, 10 has
been inserted into the V820 control panel and activated by means of the respective parameter 292.
!
The stitches for start and end backtack and stitch counting as well as the compensating stitches for the light barrier
function can be programmed individually for each seam section.
!
Several counted seam sections can be linked (9 key).
Attention!
The “TEACH IN“ function has been changed as compared to the 62 and 82 type series!
Seams and/or patterns can be added by pressing the
INSERT F1
key or erased by pressing the
DELETE F2
key. Before
programming new patterns and/or seams it is advisable to erase previously saved patterns and/or seams by pressing the
DELETE
F2
key according to chapter “Deleting a Seam or Pattern“. If patterns or seams are to be inserted between
existing ones, press the
INSERT F1
key according to chapter “Inserting a Seam or Pattern“.
Example:
3 patterns are in the memory. Delete the 2nd pattern by pressing the
DELETE F2
key. The 3rd pattern takes the
place of the 2nd pattern. A new 2nd pattern can be intalled by pressing the
INSERT F1
key. The pattern in 2nd place will
go back to being pattern no. 3.
If patterns and/or seams are only to be added, proceed as described in the following chapters.
The figure below shows all the functions assigned to programming of seams TEACH IN.
1
= Single start backtack On (lefthand arrow)
Double start backtack On (righthand arrow)
Start backtack Off
2
= Counted seam forward On (lefthand arrow)
Counted seam backward On (righthand arrow)
Counted seam Off
3
= Light barrier uncovered/covered On (lefthand arrow)
Light barrier covered/uncovered On (righthand arrow)
Light barrier Off
4
= Single end backtack On (lefthand arrow)
Double end backtack On (righthand arrow)
End backtack Off
5
= Thread trimmer On (lefthand arrow)
Thread wiper On (righthand arrow)
Thread trimmer and thread wiper On (both arrows)
Thread trimmer and thread wiper Off
6
= Sewing foot in the seam On (lefthand arrow)
Sewing foot after seam end On (righthand arrow)
Sewing foot in the seam and after seam end On
(both arrows)
Sewing foot Off
7
= Basic position down (lefthand arrow)
Basic position up (righthand arrow)
8
= Signal A1 On (lefthand arrow)
Signal A2 On (righthand arrow)
Signal A1 and A2 On (both arrows)
Signal A1 and A2 Off
9
= Switching from one seam to the next On
(lefthand arrow)
Switching from one seam to the next Off
10 = Programmed seams TEACH IN On (lefthand arrow)
Programmed seams TEACH IN Off
11 = Program symbol
12 = Display of program number
13 = Seam symbol
14 = Display of seam number
15 = Symbol for number of stitches of a seam
16 = Display of number of stitches
17 = Light barrier symbol
18 = Display of light barrier compensating stitches
19 = Arrow for TEACH IN
A = INSERT
"
Insert seams or patterns
B = DELETE
"
Delete seams or patterns
7
16
7
2
1
1
2
3
4
4
3
5
6
6
5
13 14
12
11
15
B
E
DELETE
8
9
9
8
1
2
0
A
10
INSERT
F1
18
17
19
P
+
6
K L2 3 69
F2
-