Eaton Moeller SmartWire-Darwin EU5C-SWD-CAN Hardware And Engineering Download Page 59 | Manualshive

Page: 59 / 108

background image

Putting the SmartWire Darwin
network into operation

55

02/09 AWB2723-1612en

Switching on when the gateway target configuration
is stored

If a configuration is stored in the gateway, each time the
supply voltage is switched on it is checked whether the
slaves actually found on the network comply with the stored
gateway target configuration. The result of the check is
displayed via the SmartWire-Darwin status LED on the
gateway:

Creating field bus communication

If a data interchange is possible between the SmartWire-
Darwin slaves and the gateway, in principle communication
between the gateway and the controller can also be
performed via CANopen.

X

Connect the CANopen gateway to the field bus.

X

Load the program into the PLC.

The configuration of the CANopen network is transferred to
the PROFIBUS master when the program is uploaded onto
the controller. The configuration of the SmartWire Darwin
network is now transferred to the gateway and checked by
the CANopen master (this is only the case, if you have

Description

SmartWire Darwin
status LED

Data interchange
between the gateway and
SmartWire Darwin slaves

The current actual configuration complies
with the gateway target configuration.

Green continuous light

yes

A necessary SWD slave is missing or the
gateway target configuration does not
comply with the actual configuration.

Flashing (red)

no

Slave addressing is active (after power on
or the download of a planned
configuration with empty modules).

Flashing (green)

no

Short circuit on the 15 V power supply or
no SmartWire Darwin slave is connected.

Red continuous light

no

«
...
57
58
59
60
61
...
»

Summary of Contents for Moeller SmartWire-Darwin EU5C-SWD-CAN













































































































Reviews:

No comments

Related manuals for Moeller SmartWire-Darwin EU5C-SWD-CAN

Brand: jbc Pages: 4

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 27

Brand: Panasonic Pages: 168

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 29

Brand: Panasonic Pages: 37

Brand: Panasonic Pages: 9

Brand: Garmin Pages: 220

Brand: Gardena Pages: 16

Brand: IAI Pages: 5

Brand: RadioMaster Pages: 10

Brand: Xblue Networks Pages: 2

Brand: Eaton Pages: 96

Brand: Mitsubishi Pages: 16

Brand: SOMFY Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands