Eaton Moeller SmartWire-Darwin EU5C-SWD-CAN Hardware And Engineering Download Page 69

Page: 69 / 108

easySoft-CoDeSys

02/09 AWB2723-1612en

Guarding mechanisms

Node guarding or heartbeat can be used to monitor
communication between the gateway and the CAN master.

Node guarding

Node guarding is supported. The monitoring interval (guard
time) and the number of repeat attempts can be set. Node
guarding is deactivated as standard.

Heartbeat

If the option

Activate heartbeat creation

is selected, the

module emits heartbeats at the millisecond intervals
specified in

Heartbeat producer time

. If the value is 0, the

function is deactivated.

The following illustration shows the register with the CAN
parameters.

The node guarding mechanism cannot be operated
together with the heartbeat monitoring.

Summary of Contents for Moeller SmartWire-Darwin EU5C-SWD-CAN













































































































Search results

Summary of Contents for Moeller SmartWire-Darwin EU5C-SWD-CAN

Reviews:

Related manuals for Moeller SmartWire-Darwin EU5C-SWD-CAN

Brands by name

Popular brands

Eaton Moeller SmartWire-Darwin EU5C-SWD-CAN, Hardware And Engineering

Search results

Summary of Contents for Moeller SmartWire-Darwin EU5C-SWD-CAN

Reviews:

Related manuals for Moeller SmartWire-Darwin EU5C-SWD-CAN

Brands by name

Popular brands