Dynojet 24xLC2 Linx Installation Manual Download Page 5 | Manualshive

Page: 5 / 68

background image

1

Linx with Atra Flex Installation for Model 424 Automotive Dynamometers

L

INX

WITH

A

TRA

F

LEX

I

NSTALLATION

The Linx belt drive system synchronizes the speed of the front and rear drums for
testing sensitive all-wheel drive and two-wheel drive vehicles with traction control
while the atra flex system reduces vibration and wear on the drive system.
The Linx belt drive system is designed for all-wheel drive vehicles. The Linx belt drive
system keeps the driving wheels of an all-wheel drive vehicle spinning at the same
speed to avoid driveline damage. When the Linx is used with two-wheel drive vehicles
to spin the non-driving wheels for the purpose of not throwing codes, extra attention
will be needed for the proper adjustment of the Linx belt.
Always monitor the front and rear drum speed with every vehicle tested. When the drum
speed starts to vary more than a couple of miles per hour, belt adjustment is needed.
This document is designed to help you install the Linx with Atra Flex system on your
model 424 automotive dyno. To ensure safety and accuracy in the procedures,
perform the procedures as they are described.
Document Part Number: 98200073
Version 3
Last Updated: 01-14-2020
This chapter is divided into the following categories:
• Introduction, page 2
• Linx Belt Drive Specifications, page 3
• Unpacking the Linx Parts, page 4
• Dynojet Logo Panels and Pit Covers, page 10
• Carrier Bearing and Splined Shaft Installation, page 14
• Inner Mounting Plate and Flange Bearing Installation, page 15
• Drive Pulley Installation, page 19
• Idler Pulley Installation, page 23
• Belt and Tensioner Pulley Assembly Installation, page 24
• Outer Carrier Bearing Installation, page 31
• Atra Flex Coupler Installation, page 32
• Upper Pulley Mount Installation, page 35
• Routing the Linx Detect Sensor Cable, page 38
• Brake Signal Relay Installation, page 40
• Tension the Belt, page 42
• Linx Belt Covers—Above Ground, page 44
• Linx Belt Covers—In Ground, page 52
• Disconnect the Belt Drive from the Dyno Drums, page 56

«
...
3
4
5
6
7
...
»

Summary of Contents for 24xLC2 Linx





































































Reviews:

No comments

Related manuals for 24xLC2 Linx

Brand: LAUMAS Pages: 40

Brand: Accel Pages: 2

HOIST-A-TOP JL CRANK

Brand: Lange Originals Pages: 13

Brand: Raven Pages: 70

Brand: RAM Pages: 292

Brand: RAM Pages: 116

COPENHAGEN WHEEL

Brand: Superpedestrian Pages: 52

Brand: Metra Electronics Pages: 12

Brand: Halfords Pages: 4

Brand: Fisher-Price Pages: 8

Brand: Whispbar Pages: 15

Brand: FORM FIT Pages: 2

Brand: Hettich Pages: 2

Brand: Beurer Pages: 24

Brand: SimpliPhi Pages: 15

MOBILE COOLING TROPICOOL TC07

Brand: Dometic Pages: 156

HANDLEBAR CONSOLE

Brand: Burley Pages: 2

Evolion 2.1 kWh

Brand: Saft Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands