manualshive.com logo in svg

Dynojet 24xLC2 Linx, Installation Manual

Share
Download
Dynojet 24xLC2 Linx Installation Manual Download Page 42

L I N X   W I T H   A T R A   F L E X   I N S T A L L A T I O N

Routing the Linx Detect Sensor Cable

Linx with Atra Flex Installation for Model 424 Automotive Dynamometers

38

     

ROUTING THE LINX DETECT SENSOR CABLE

Use the following instructions along with Figure 31 on page 38 to route the Linx detect 
sensor cable to the DynoWare RT module.

You will need the following parts:

• 197104130 Zip Tie, 4" (18)
• 15300016

Adhesive Mounting Pads (15)

1

Route the Linx detect sensor cable up and over the movable dyno pulley, along the 
back of the dyno, and over to the cable track.

2

Using the supplied adhesive mounting pads and cable ties, secure the Linx detect 
sensor cable to the pulley mounts and dyno.

Note: 

You may wish to secure any additional cables with the Linx detect sensor 

cable for a clean installation.

Figure 31: Routing the Linx Detect Sensor Cable

Linx detect 

sensor cable

movable dyno 

pulley

Linx detect 

sensor cable

cable track

adhesive mounting 

pad and cable tie

Summary of Contents for 24xLC2 Linx





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands