manualshive.com logo in svg

Dynojet 24xLC2 Linx, Installation Manual

Share
Download
Dynojet 24xLC2 Linx Installation Manual Download Page 50

L I N X   W I T H   A T R A   F L E X   I N S T A L L A T I O N

Linx Belt Covers—Above Ground

Linx with Atra Flex Installation for Model 424 Automotive Dynamometers

46

     

7

Remove the 1/4-20 x 5/8-inch torx screw from the outer most tube of the dyno 
bridge as shown in Figure 37.

8

Remove the screw from the drum guard on the stationary dyno as shown 

in Figure 37.

9

Turn the cover assembly over and move towards the dyno.

10 Place the cover assembly so the center support is on the outer tube with the hole 

lined up as shown and the right support is on the stationary dyno with the hole 
lined up as shown.

Note: 

For extended wheelbase options, use the hole in the center support shown 

in Figure 37.

11 Secure the right cover assembly to the outer bridge tube and the stationary dyno 

drum guard using the two screws removed earlier.

Figure 37: Install the Right Cover Assembly to the Dyno

right support secured 

to drum guard

center support 

secured to bridge

extended wheelbase options

center support secured to bridge

use this hole

Summary of Contents for 24xLC2 Linx





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands