Dynojet 24xLC2 Linx Installation Manual Download Page 30

Page: 30 / 68

L I N X W I T H A T R A F L E X I N S T A L L A T I O N

Pulley Mounting Plates and Outer Bearings Installation

Linx with Atra Flex Installation for Model 424 Automotive Dynamometers

PULLEY MOUNTING PLATES AND OUTER BEARINGS INSTALLATION

The inner pulley mounting plates and the pulley mounts are stamped with numbers to
help match the parts and guide you in the installation process.

You will need the following parts:

• 21200091

Idler Pulley Bearing Mounting Plate

• 21600065

Linx Detect Sensor Mounting Bracket

• 21600067

Linx Detect Sensor Tab

• 21600080

Linx Detect Sensor Mounting Plate

• 22400015

Linx Detect Sensor Pickup Collar

• 32300001

Flange Bearing with Lock Collar

• 36540643

Screw, 8-32 x 3/8", Pan-Head, Phil (5)

• 36711100

Nut, 9/16-12, Hex (4)

• 36811640

Bolt, 9/16-12 x 2", Hex (4)

• 36900001

Washer, 1/4", Lock (4)

• 36923100

Washer, 3/8", Flat (64)

• 36943101

Washer, 9/16", Flat (4)

• 43400003

Zip Tie, 6" (2)

• 61300022

Pulley Mount, Upper, Stationary Dyno

• 61300023

Pulley Mount, Lower, Stationary Dyno (3)



used for stationary dyno pulley, lower



movable dyno pulley, upper



idler pulley

• 61300025

Pulley Mount, Upper, Idler Pulley

• 61300026

Pulley Mount, Lower, Movable Dyno

• 68300002

Linx Detect Sensor

• 76950665

Linx Detect Sensor Cable

• DM150-019-012 Bolt, 3/8-16 x 1", Hex (64)

Summary of Contents for 24xLC2 Linx





































































Search results

Summary of Contents for 24xLC2 Linx

Reviews:

Related manuals for 24xLC2 Linx

Brands by name

Popular brands

Dynojet 24xLC2 Linx, Installation Manual

Search results

Summary of Contents for 24xLC2 Linx

Reviews:

Related manuals for 24xLC2 Linx

Brands by name

Popular brands