Dynojet 24xLC2 Linx Installation Manual Download Page 48

Page: 48 / 68

L I N X W I T H A T R A F L E X I N S T A L L A T I O N

Linx Belt Covers—Above Ground

Linx with Atra Flex Installation for Model 424 Automotive Dynamometers

LINX BELT COVERS—ABOVE GROUND

You will need the following parts:

• 11700001

Door Magnet (4)

• 15300015

Double Sided Tape

• 21200187

End Panel (2)

• 21200188

Lid Assembly (2)

• 21600076

Center Leg

• 21600078

Belt Cover Center Support

• 21600082

Belt Cover Right Support

• 21600102

Belt Cover Logo Leg (2)

• 21700023

Brace (4)

• 36468100

Nut, 1/4-20, Nylock (66)

• 36561045

Screw, 1/4-20 x 5/8", Pan-Head, Torx (37)

• 61300081

Left Door Assembly

• 61300082

Right Door Assembly

• DM150-009-003 Washer, 1/4", Flat (33)

NSTALLING

THE

IGHT

OVER

SSEMBLY

Use the following instructions to assemble and install the right Linx cover assembly.

Place two braces on the floor.

Secure the end panel to the braces using two 1/4-20 nuts.

Secure the right leg to the braces as shown using four 1/4-20 nuts.

Secure the center leg to the braces as shown using two 1/4-20 nuts.

Figure 35: Install the Legs and End Panel—Right Cover Assembly

brace

end panel

right leg

center leg

Summary of Contents for 24xLC2 Linx





































































Search results

Summary of Contents for 24xLC2 Linx

Reviews:

Related manuals for 24xLC2 Linx

Brands by name

Popular brands

Dynojet 24xLC2 Linx, Installation Manual

Search results

Summary of Contents for 24xLC2 Linx

Reviews:

Related manuals for 24xLC2 Linx

Brands by name

Popular brands