manualshive.com logo in svg

Dynojet 24xLC2 Linx, Installation Manual

Share
Download
Dynojet 24xLC2 Linx Installation Manual Download Page 43

     

39

L I N X   W I T H   A T R A   F L E X   I N S T A L L A T I O N

Routing the Linx Detect Sensor Cable

Version 3

Linx with Atra Flex Installation for Model 424 Automotive Dynamometers

3

Remove the two screws and washers securing the cable track containing the signal 
cables to the front rail tie assembly. Pull the cable track out from under the dyno.

Note: 

Do not place the Linx detect sensor cable in the track with the power 

cables. Keep the power cables in a separate track from the signal cables.

4

Using a screwdriver, open the crossbar on each link.

5

Place the Linx detect sensor cable in the cable track and close the crossbar on each 
link.

Figure 32: Cable Track Link Crossbar

6

Place the cable track back under the dyno and secure the cable track to the front 
rail tie assembly using the screws and washers removed earlier.

7

Route the Linx detect sensor cable to the back of the DynoWare RT module and 
connect the cable to Linx 1 as shown in Figure 31 on page 38.

crossbar

cable track link

use screwdriver 

to open

Summary of Contents for 24xLC2 Linx





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands