Dynojet 24xLC2 Linx Installation Manual Download Page 56

Page: 56 / 68

L I N X W I T H A T R A F L E X I N S T A L L A T I O N

Linx Belt Covers—In Ground

Linx with Atra Flex Installation for Model 424 Automotive Dynamometers

LINX BELT COVERS—IN GROUND

You will need the following parts:

• 21200098

Pit Cover Mount

• 21217513

Calibration Access Cover (2)

• 21600026

Belt Cover, Center Support

• 21919101

Feet, Pit Cover (6)

• 36561045

Screw, 1/4-20 x 5/8", Pan-Head, Torx (16)

• 36580434

Bolt, 3/8-16 x 1/2" Button-Head Flange, Allen (8)

• 36923100

Washer, 3/8", Flat (6)

• 37513200

Anchor, Red Head, 3/8" (6)

• 61329400P

Pit Retarder Cover Assembly (2)

• DM150-019-012 Bolt, 3/8-16 x 1", Hex (6)
• DM150-020-005 Nut-Crush, 1/4-20 (4)

Secure the center support to the pit cover mount using four 1/4-20 x 5/8-inch torx
screws and four 1/4-20 nuts.

Note:

When the dyno is equipped with the wheelbase extension kit



(P/N 61119183), use the center support (P/N 21200176) included in the kit.

Figure 43: Install the Center Support to the Pit Cover Mount

pit cover mount

center support

pit cover mount

center support

center support included with

wheelbase extension kit

Summary of Contents for 24xLC2 Linx





































































Search results

Summary of Contents for 24xLC2 Linx

Reviews:

Related manuals for 24xLC2 Linx

Brands by name

Popular brands

Dynojet 24xLC2 Linx, Installation Manual

Search results

Summary of Contents for 24xLC2 Linx

Reviews:

Related manuals for 24xLC2 Linx

Brands by name

Popular brands