manualshive.com logo in svg

Dynojet 24xLC2 Linx, Installation Manual

Share
Download
Dynojet 24xLC2 Linx Installation Manual Download Page 39

     

35

L I N X   W I T H   A T R A   F L E X   I N S T A L L A T I O N

Upper Pulley Mount Installation

Version 3

Linx with Atra Flex Installation for Model 424 Automotive Dynamometers

UPPER PULLEY MOUNT INSTALLATION

Use the following instructions to install the upper pulley mounts on both the 
stationary and movable dynos.

The upper pulley mounts are stamped with numbers to help match the parts and guide 
you in the installation process.

I

NSTALLING

 

THE

 U

PPER

 D

RIVE

 P

ULLEY

 

AND

 U

PPER

 I

DLER

 P

ULLEY

 M

OUNTS

1

Place a lower stationary dyno pulley mount (P/N 61300023, stamped 2) over the 
movable dyno pulley and loosely secure the mount to the inner plate using 

five 3/8-16 x 1-inch bolts and five 3/8-inch flat washers (one of the holes in the 
pulley mount is not used).

2

Loosely secure the pulley mount to the movable dyno pulley bearing plate using 
five 3/8-16 x 1-inch bolts and five 3/8-inch flat washers.

Figure 28: Install the Pulley Mount Over the Movable Dyno Pulley

pulley mount

P/N 61300023

stamped 2

Summary of Contents for 24xLC2 Linx





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands