Dynojet 24xLC2 Linx Installation Manual Download Page 33

Page: 33 / 68

L I N X W I T H A T R A F L E X I N S T A L L A T I O N

Pulley Mounting Plates and Outer Bearings Installation

Version 3

Linx with Atra Flex Installation for Model 424 Automotive Dynamometers

12 With the mounting bracket screws loose, slide the mounting plate and sensor until

the Linx detect sensor tab is centered in the sensor window.

13 Tighten the screws securing the mounting plate and sensor assembly to the

mounting bracket.

Figure 21: Align the Linx Detect Sensor Tab

NSTALLING

THE

OVABLE

YNO

OWER

ULLEY

OUNT

Place the lower movable dyno pulley mount (P/N 61300026, stamped 4) under
the movable dyno pulley and loosely secure the mount to the inner plate using



five 3/8-16 x 1-inch bolts and five 3/8-inch flat washers.

Loosely secure the pulley mount to the movable dyno pulley bearing plate using
three 3/8-16 x 1-inch bolts and three 3/8-inch flat washers.

Figure 22: Install the Pulley Mount Under the Movable Dyno Pulley

mounting bracket

pickup collar

sensor

sensor window

tab

tighten screws

mounting plate

pulley mount

P/N 61300026

stamped 4

Summary of Contents for 24xLC2 Linx





































































Search results

Summary of Contents for 24xLC2 Linx

Reviews:

Related manuals for 24xLC2 Linx

Brands by name

Popular brands

Dynojet 24xLC2 Linx, Installation Manual

Search results

Summary of Contents for 24xLC2 Linx

Reviews:

Related manuals for 24xLC2 Linx

Brands by name

Popular brands