Dynojet 24xLC2 Linx Installation Manual Download

Page: 23 / 68

L I N X W I T H A T R A F L E X I N S T A L L A T I O N

Drive Pulley Installation

Version 3

Linx with Atra Flex Installation for Model 424 Automotive Dynamometers

DRIVE PULLEY INSTALLATION

Use the following instructions to install the drive pulleys for both the movable and
stationary dynos.

You will need the following parts:

• 21200083

Stationary Dyno Pulley Bearing Mounting Plate

• 21200090

Movable Dyno Pulley Bearing Mounting Plate

• 32300001

Flange Bearing with Lock Collar

• 32300002 Bushing (2)



includes three bolts and lock washers each

• 32300003

Grooved Pulley (2)

• 36711100

Nut, 9/16-12, Hex (8)

• 36811640

Bolt, 9/16-12 x 2", Hex (8)

• 36943101

Washer, 9/16", Flat (8)

• 61300068

Outer Shaft (2)

Secure the flange bearing to the pulley bearing mounting plate using four



9/16-12 x 2-inch bolts, four 9/16-inch flat washers, and four 9/16-inch nuts.

Slide the pulley bearing mounting plate assembly over the outer shaft.

Using the installation instructions in

Appendix B

, loosely secure the bearing cap

screw.

Figure 11: Install the Pulley Bearing Mounting Plate

pulley bearing

mounting plate

outer shaft

flange bearing

Summary of Contents for 24xLC2 Linx





































































Search results

Summary of Contents for 24xLC2 Linx

Reviews:

Related manuals for 24xLC2 Linx

Brands by name

Popular brands

Dynojet 24xLC2 Linx, Installation Manual

Search results

Summary of Contents for 24xLC2 Linx

Reviews:

Related manuals for 24xLC2 Linx

Brands by name

Popular brands