Dynojet 24xLC2 Linx Installation Manual Download

Page: 27 / 68

L I N X W I T H A T R A F L E X I N S T A L L A T I O N

Idler Pulley Installation

Version 3

Linx with Atra Flex Installation for Model 424 Automotive Dynamometers

IDLER PULLEY INSTALLATION

You will need the following parts:

• 32300001

Flange Bearing with Lock Collar

• 36711100

Nut, 9/16-12, Hex (4)

• 36943101

Washer, 9/16", Flat (4)

• 61100007

Idler Pulley Assembly

Place the flange bearing on the threaded studs on the inner plate.

Secure the flange bearing to the inner plate using four 9/16-inch flat washers and



four 9/16-inch nuts.

Holding the idler assembly horizontal, slide the assembly into the bearing until its
outer edge is approximately 11-1/8-inches from the face of the inner plate.

Using the installation instructions in

Appendix B

, secure the lock collar.

Note:

Refer to

Appendix B

for bearing installation instructions.

Carefully allow the idler pulley assembly to hang in the bearing.

Figure 15: Install the Idler Pulley

flange bearing

idler pulley assembly

Summary of Contents for 24xLC2 Linx





































































Search results

Summary of Contents for 24xLC2 Linx

Reviews:

Related manuals for 24xLC2 Linx

Brands by name

Popular brands

Dynojet 24xLC2 Linx, Installation Manual

Search results

Summary of Contents for 24xLC2 Linx

Reviews:

Related manuals for 24xLC2 Linx

Brands by name

Popular brands