manualshive.com logo in svg

DSC Envoy NT9010, Installation Manual, Page: 8 / 64

Share
Download
DSC Envoy NT9010 Installation Manual Download Page 8

C h a p t e r   1 :   Q u i c k   S e t   U p

4

WLS914-433 Dual PIR Wireless Motion Detector

The dual PIR wireless motion detector can be used to provide wireless space protection. The
unit comes with four AA batteries

.

WLS925L-433 Mini Wireless Universal Transmitter

The WLS925L-433 wireless universal transmitter is a smaller transmitter that can be used
for door and window contacts. The unit comes with one Lithium battery and has built-in
contacts.

WLS919-433 Wireless Key

The wireless key can be used to provide a simple and mobile method of arming and dis-
arming the system. The unit comes with two CR2032 lithium batteries.

This system can have a maximum of 16 Wireless Keys.

NT9201 Remote Sounder

You can connect a hardwired remote sounder to the NT9010 system. This sounder provides
an additional station for the NT9010 to sound alarms and system status, and for central
station talk/listen-in sessions. 

NOTE:

Maximum distance for the Remote Sounder is 500ft (152m) using 22AWG

sheilded cable.

1.1.5 Peel-off 

Instruction 
Labels

The Envoy unit comes with a set of peel-off instruction labels already applied. Installer
should remove these labels after installation. For future programming needs, please see
sample labels below for instructions.

The NT9010's "Flash" programming will help you to quickly set up the system.

To begin:

1. Press [ ][8]

2. Enter the default installer’s code: [5555]

3. Follow the audio instruction

buttons [A] to [F] for entering letters in serial numbers.

✱

For contacts used on the hardwired zones:

Enter serial number 200001 for the first hardwired zone

Enter serial number 200002 for the second hardwired zone.

Use

!

!

1

= YES

2

= NO

Selection

Type 2 (TX)

Type 3 (PIR)

Type 4 (Smoke)

[A] Preset

Front Door

Main Floor Motion

Main Floor Fire

[B] Preset

Back Door

Upstairs Motion

Upstairs Fire

[C] Preset

Garage Door

Downstairs Motion

Downstairs Fire

[D] Preset

Window

Hallway Motion

Hallway Fire

[E] Preset

Patio Door

Garage Motion

Garage Fire

Please use

buttons [A] to [E] for standard label options

ALSO REFER TO INSTALLATION MANUAL

PEELOFF

A = Stay
B = Away

C = Chime

D = Exit
E = Status

F = Volume
Back = Record
Forward = Playback

Summary of Contents for Envoy NT9010

































































Reviews:

No comments