manualshive.com logo in svg

DSC Envoy NT9010, Installation Manual, Page: 21 / 64

Share
Download
DSC Envoy NT9010 Installation Manual Download Page 21

S e c t i o n   2 . 1 :   P r o g r a m m i n g   t h e   N T 9 0 1 0

1 7

Adding Numbers to Labels

Three special Number Commands are available to allow the system to include a number in
the voice label. The number commands allow the system to announce the number in three
different modes:

Label 000: Number Command 1, Combined Form.

 The number will be announced in its

full form. For example, the number 401 would be announced as “four hundred and one”.

Label 001: Number Command 2, Ordered Form.

 The number will be announced in a

descriptive form. For example, the number 401 would be announced as “four hundred and
first”.

Label 002: Number Command 3, Individual Numbers.

 Each digit in the number will be

announced individually. For example, the number 401 would be announced as “four zero
one”.

The number commands take up two of the six available word spaces in a label. In the first
space select the type of announcement for the number (Number Command 000, 001 or
002). In the second space program the 3-digit number to be read (from 000 to 999). 

NOTE:

 Because number commands take up 2 label spaces, you cannot program

them in the sixth entry spot for a label.

Recording Custom Labels

You can record up to five custom labels for the system and for the zones using program-
ming sections [701] to [705]. You can use any of these labels for the system or zone labels,
instead of the words available in the Audio Label Library. To record a custom label:

1. From Advanced Programming, enter [807].

2. Enter one of sub-sections [701] to [705].

3. Press the Record function key on the NT9010.

4. Speak into the NT9010 microphone. Each label can be up to 1.5 seconds long. To

stop recording, press [#].

5. When you are finished recording, press the Playback function key. The NT9010 plays

your recorded label back to you. To listen to the label again, press Playback again.

6. If you want to re-record the label, press the Record function key again.

7.  To record more labels, repeat steps 1 to 5.

NOTE:

 If the NT9010 is completely powered down (both AC and battery power

are lost), the recorded labels will be lost.

2.1.6 Reviewing 

Programming

To review the current programming for a section enter the 3-digit section number. The
NT9010 will announce the data programmed. If the programming is correct press [#] to exit
the section, otherwise enter the correct data.

2.1.7 Exiting 

Programming

When the NT9010 announces “Enter Section Number”, press the [#] key.

Summary of Contents for Envoy NT9010

































































Reviews:

No comments