manualshive.com logo in svg

DSC Envoy NT9010, Installation Manual, Page: 17 / 64

Share
Download
DSC Envoy NT9010 Installation Manual Download Page 17

S e c t i o n   1 . 2 :   I n s t a l l i n g   T h e   N T 9 0 1 0

1 3

1.2.8 Other NT9010 

Options

After all zones have passed the Placement Test, Flash Programming will move to the
advanced programming sections. If you do not need to do more programming, press [#] to
exit.

If you need to complete programming not covered by Flash Programming, please see

Chapter 2: Advanced Programming

 on page 15 . For example, you may need to change

the definitions of one or more zones. This programming is described in 

2.3.1 Zone Defini-

tions

 on page 33.

1.2.9 Deleting 

Wireless 
Devices

To remove a wireless device from the system, you will need to use the advanced program-
ming sections. 

1. Press [

✱

][8], then enter the Installer’s code. The default Installer’s code is [5555].

3. When prompted, press [2] to go to advanced programming.

4. Enter [804], then enter the 2-digit number of the zone you want to delete (01 - 32).

The system announces the current serial number for the zone.

5. Program the serial number for the zone as [000000]. The wireless device for the

zone will be removed.

NOTE:

 You may need to remove power from the system and then restore it to

clear troubles caused by deleted zones.

Summary of Contents for Envoy NT9010

































































Reviews:

No comments