manualshive.com logo in svg

DSC Envoy NT9010, Installation Manual, Page: 35 / 64

Share
Download
DSC Envoy NT9010 Installation Manual Download Page 35

S e c t i o n   2 . 2 :   C ha ng i n g  H o w  t h e   N T 9 0 1 0   W o r k s   F o r  U s e r s

3 1

3. Enter the 2-digit code from the list below for the function you want the button to

have:

4. Repeat steps 1 to 3 until all buttons are programmed.

* Do not use for UL Listed installations

NOTE:

 Control unit must have the ‘Arm/Disarm Bell Squawk’ feature enabled

when using wireless key devices. When placing the control unit, ensure the bell
squawk can be heard from outside the home.

Wireless Key Function 
Button Programming  . . . . . . . . . . . . . . . . . . . . . . Sections [804]-[61] to [804]-[64]
WLS Key Does Not Use Access Codes . . . . . . . . . . . . . . . .Section [017], Option [1]

2.2.12Fire, Auxiliary 

or Medical, 
and Panic 
Keys

Three emergency keys are available on the NT9010. Each pair of keys must be pressed and
held for 2 seconds before they will activate. This 2 second delay is designed to help prevent
accidental activation. If the 

Fire Keys 

option is enabled, when the Fire keys are pressed and

held for 2 seconds, the system will activate the alarm output. It pulses one second on, one
second off only if option 8 of Section [013] is disabled (Standard Fire option). If 

Fire Bell

Continuous

 is selected the alarm output will sound until a code is entered; otherwise it will

sound until a code is entered or the alarm output times out. Communication of the signal
to central station is immediate.

If the Auxiliary (

) or Medical (

)* keys are pressed and held for 2 seconds, the unit

beeps three times to verify activation. The system will beep the keypad ten times rapidly to
verify communication to the central station.

If the

 

Panic keys are pressed and held for 2 seconds, the system will immediately communi-

cate the signal to central station. If 

Panic Keys Audible

 is enabled, the system will beep

the keypad three times upon activation and activate the alarm output until a code is
entered or the alarm output times out. Otherwise the alarm will be completely silent.

NOTE:

The Fire, Auxiliary or Medical, Panic keys will operate even if Keypad

Lockout is active (see 2.2.13 Keypad Options on page 32).

Fire Keys Enable  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Section [015], Option [1]
Panic Keys Audible . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Section [015], Option [2]
Fire Bell Continuous  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Section [014], Option [8]

*If the unit is to be used in home health care applications, the unit must have Medical ( )
keys and not Auxiliary (

) keys.

Entry Description

00

Null Key (Key not used)

03

Stay Arm

04

Away Arm

05

No entry delay arming*

06

Door Chime On/Off

07

System Test

16

Quick Exit

17

Activate Stay/Away Zones

27

Disarm (Off)

28

Fire Alarm*

29

Auxiliary or Medical Alarm

30

Panic Alarm

Summary of Contents for Envoy NT9010

































































Reviews:

No comments