manualshive.com logo in svg

DSC Envoy NT9010, Installation Manual, Page: 12 / 64

Share
Download
DSC Envoy NT9010 Installation Manual Download Page 12

C h a p t e r   1 :   Q u i c k   S e t   U p

8

Single End of Line loops. Please refer to the following sections to study each type of individ-
ually supervised zone wiring. 

Normally Closed (NC) Loops

To enable normally closed loops, programming section [013], option [1] must be ON.

NOTE:

 This option should only be selected if Normally Closed (NC) devices/con-

tacts are being used.

Normally Closed Loops . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [013], Option [1]

Single End Of Line (EOL) Resistors

To enable system detection of single end of line resistors, programming section [013],
option [1] must be OFF.

NOTE:

This option should be selected if either Normally Closed (NC) or Normally

Open (NO) detection devices or contacts are being used.

End of Line Resistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [013], Option [1]

Keyswitch Zone Wiring

Zones may be programmed to be used as key-
switch arming zones and must be wired
according to the following diagram:

For a complete description of how keyswitch
zones operate, see 

2.3.1 Zone Definitions

 on

page 33

.

Summary of Contents for Envoy NT9010

































































Reviews:

No comments