manualshive.com logo in svg

DSC Envoy NT9010, Installation Manual, Page: 15 / 64

Share
Download
DSC Envoy NT9010 Installation Manual Download Page 15

S e c t i o n   1 . 2 :   I n s t a l l i n g   T h e   N T 9 0 1 0

1 1

[05] Interior Stay/Away Zone:

 If this type of zone is violated when the sys-

tem is armed (e.g. the motion detector senses motion), an instant alarm
will be generated unless a Delay Zone is violated first. If a Delay Zone is
violated first, this zone will also follow the entry delay. 

The zone will be automatically bypassed under the following conditions:

■

the NT9010 is armed in the Stay Mode

■

the NT9010 is armed without entry delay ([

✱

][9] arming)

■

the NT9010 is armed with an access code and during the exit delay a Delay 
zone is NOT violated (user does not go through the entry/exit door).

If zones are automatically bypassed, the user can reactivate the zones by
entering [

✱

][1].

[87] Delayed 24 Hour Fire (Wireless): 

If this zone is violated (e.g. the smoke

detector senses smoke), the alarm will immediately sound, but the alarm
communication to the central station will be delayed for 30 seconds. If
during the 30 second delay the user presses the [#] key, the alarm and
communicator will be delayed an additional 90 seconds. This provides
time for a user to correct the problem. 

If after the 90 second delay the zone is still violated the process will begin
again: the alarm will sound but the alarm communication will be delayed
for 30 seconds.

If the user does not press the [#] key, after 30 seconds the alarm will latch
on and the system will communicate a fire alarm to the central station.
The alarm will sound until the Bell Cutoff time expires, or until a valid
code is entered.

Programming Zone Labels

If an enrolled device is a door/window contact, motion detector, glassbreak detector, or
smoke detector the system will then prompt you to enter an audio label for the new zone.
You can choose from any of the following preset audio labels:

If necessary, you can also program custom labels for the zones through the NT9010 Flash
Programming.

Press 

Function 

Key:

Door/window 

contacts 

(2XXXXX)

Motion or 

glassbreak 

detector 

(3XXXXX)

Smoke detector 

(4XXXXX)

A

Front door

Main floor motion

Main floor fire

B

Back door

Upstairs motion

Upstairs fire

C

Garage door

Downstairs motion

Downstairs fire

D

Window

Hallway motion

Hallway fire

E

Patio door

Garage motion

Garage fire

Summary of Contents for Envoy NT9010

































































Reviews:

No comments