S e c t i o n 2 . 3 : C ha ng i ng O t he r N T 9 0 1 0 Fu n c t i o n s
4 7
The time to complete a successful download can be significantly reduced with the use of
the PC-Link adaptor. This adaptor makes it possible to perform on-site downloading.
To perform PC-LINK please do the following:
• Set up the downloading computer close to where the NT9010 is installed.
• Remove the NT9010 from the top two latches and allow the unit to sit at a 90
degree angle to the backplate. The unit may also be completely removed from the
backplate.
• Connect the PC-LINK header in the slot provided in the back of the unit.
• Ensure that the downloading computer has initiated the PC-LINK session.
To
Initiate Local Downloading via PC-Link
, enter [
✱
] [8] [Installer’s Code] [499]
[Installer’s Code] [499]. The keypad will be busy for the duration of the PC-Link connection.
The status LEDs will display the current system status. For more information on connecting
the PC-Link adaptor, refer to your “PC-Link Download Kit Instruction Sheet”.
Answering Machine/Double Call . . . . . . . . . . . . . . . . . . . .Section [401], Option [1]
User Enable DLS Window . . . . . . . . . . . . . . . . . . . . . . . . .Section [401], Option [2]
Call Back. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Section [401], Option [3]
User-Initiated Call-up . . . . . . . . . . . . . . . . . . . . . . . . . . . .Section [401], Option [4]
Answering Machine Double Call Timer . . . . . . . . . . . . . . . . . . . . . . . Section [405]
Download Computer Telephone Number . . . . . . . . . . . . . . . . . . . . . Section [402]
Download Access Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [403]
Panel Identifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [404]
Standard/UL Communications Priority . . . . . . . . . . . . . . . .Section [701], Option [8]
One-time 1-hour user enabled DLS window* . . . . . . . . . .Section [702], Option [7]
*Must be turned on for UL Listed installations.
2.3.15Telephone
Line
Monitoring
(TLM)
When the
TLM Enable
option is selected, the system will supervise the telephone line and
will indicate a trouble condition if the telephone line is disconnected.
If the TLM Enable option is ON, the system will check the telephone line every 10 seconds.
If the telephone line voltage is below 3V for the number of checks programmed in the
TLM
Trouble Delay
section, the system will report a TLM trouble. The default number of checks
is 3. Enter a number from (000) to (255) in the TLM Trouble Delay section to change the
number of checks before the TLM trouble is reported. Programming a delay means that a
momentary interruption of the telephone line will not cause a trouble condition.
If the
TLM Trouble Beeps When Armed
option is enabled, the system will indicate a TLM
trouble at the keypad while the system is armed. To activate the bell output in the case of a
TLM trouble while the system is armed, the
TLM Audible (Bell) When Armed
option
must be selected.
When the trouble condition is restored, the system can send a
TLM Restoral
reporting
code. Any events which occur while the telephone line is down will also be communicated.
TLM Enable/Disable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Section [015], Option [7]
TLM Trouble Beeps When Armed
or TLM Audible (Bell) When Armed . . . . . . . . . . . . . . . . . .Section [015], Option [8]
TLM Restoral Reporting Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [350]
TLM Trouble Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [370]