manualshive.com logo in svg

DSC Envoy NT9010, Installation Manual, Page: 56 / 64

Share
Download
DSC Envoy NT9010 Installation Manual Download Page 56

5 2

A p p e n d i x   B :   R e p o r t i n g   C o d e s

The following tables contain Contact ID and Automatic SIA format reporting codes. For more information on report-
ing code formats and notes about individual reporting codes, see 

2.3.11 Communicator Reporting Formats

 on

page 39 and 

2.3.12 CommunicatorReporting Codes

 on page 42.

Contact ID

The first digit (in parentheses) will automatically be sent by the control. The second two digits are programmed to
indicate specific information about the signal.

For example, if zone 1 is an entry/exit point, you could program the event code as [34]. The central station would
receive the following:

*BURG - ENTRY/EXIT - 1

where the “1” indicates which zone went into alarm.

SIA Format - Level 2 (Hardcoded)

The SIA communication format used in this product follows the level 2 specifications of the SIA Digital Communica-
tion Standard - October 1997. This format will send the Account Code along with its data transmission. The transmis-
sion would look similar to the following at the receiver:

N Ri01

BA 01

N

= 

New  Event

Ri01 =  Area 

Identifier

BA

= Burglary 

Alarm

01

= Zone 

1

Section #

Reporting Code

Code Sent When...

Dialer 

Direction*

Automatic 
Contact ID 

Codes

SIA Auto Rep 

Codes**

[320] to 
[323]

Zone Alarms

zone goes into alarm

A/R

(1) 3A

See  Table 3

[324] to 
[327]

Zone Restorals

alarm condition has been restored

A/R

(1) 3A

[328]

Duress Alarm

duress code entered at keypad

A/R

(1) 21

HA-00

[328]

Opening After Alarm

system disarmed with alarm in memory

A/R

(4) A6

OR-00

[328]

Recent Closing

alarm occurs within two minutes of system arming

A/R

(4) 59

CR-00

[328]

Cross Zone (Police Code) 

Alarm

two zones on the system go into alarm during any 
given armed-to-armed period (incl. 24Hr zones)

A/R

(1) 4A

BV-00

[329]

[F] Key Alarm/Rest.

Keypad fire alarm (alarm and restore reporting 
codes sent together)

A/R

(1) 15

FA-00/FH-00

[329]

[A] Key Alarm/Rest.

Keypad auxiliary or medical alarm† (alarm and 
restore reporting codes sent together)

A/R

(1) AA

MA-00/MH-00

* A/R = alarms/restorals; T/R = tampers/restorals; O/C = openings/closings; MA/R = miscellaneous alarms/restorals;

T = test transmissions

** UU = user number (user01-42); ZZ = zone number (01-32)

***Program the “Fail to close” event code [(4)54] to report either closing or activity delinquency. Make sure your central

station is aware of the application of this reporting code.

****Zones are identified, panic pendants, wireless keys, and handheld keypads are not.

†If unit is to be used in home health care applications, the unit must have medical keys

 

( ) 

not auxiliary 

(

)

 

keys.

Summary of Contents for Envoy NT9010

































































Reviews:

No comments