DSC Envoy NT9010 Installation Manual Download Page 58

Page: 58 / 64

A p p e n d i x C : U L L i s t e d G r a d e A C o n t r o l U n i t R e q u i r e m e n t s

5 4

Table2: Contact ID Zone Alarm/Resto-
ral Event Codes (as per ADEMCO):

Program any of these codes for zone alarms/restorals
when using the standard (non-automatic) Contact ID
reporting format.

Table 3: SIA Format Automatic
Zone Alarm/Restoral Codes

A p p e n d i x C : U L L i s t e d G r a d e A

C o n t r o l U n i t R e q u i r e m e n t s

• Installer should verify communication format

between control unit and receiver.

• Entry delay must not exceed 45 seconds.
• Exit delay must not exceed 60 seconds.

• Minimum bell cutoff time is 4 minutes.

• Keyswitch (if used) must be mounted in a pro-

tected area.

• ‘Quick Exit’ feature must be disabled.

• ‘Bell Squawk on Trouble’ feature must be enabled.
• Minimum ‘Dialing Attempt’ must be 5 and maxi-

mum 10.

• Hardwired zones must be EOL configuration.

• ‘Code Required to Bypass Zones’ must be enabled.

• ‘Bypass Status not Displayed While Armed’ option

selected.

• ‘Test Transmission Cycle’ must be set for daily

transmission.

• ‘Keypad Lockout’ must be programmed.

• ‘Temporal Three Fire Signal’ must be enabled.

• ‘Closing Confirmation’ must be enabled.

• ‘UL Communications Priority’ must be enabled.

• ‘One time 1-hour User Enabled DLS Window’ must

be enabled.

• ‘Answering Machine/Double Call’ option must

NOT be enabled.

• ‘Wireless Supervisory Window’ must be pro-

grammed 4 hours or less.

• ‘RF Jamming Detection Zone’ must be pro-

grammed; zone type ‘Instant’.

NOTE:

This control unit is to be checked by a qualified technician at least once every 3 years.

Medical Alarms

(1)34

Entry

Exit

(1)AA Medical

(1)35 Day / Night

(1)A1 Pendant Transmitter

(1)36 Outdoor

(1)A2 Fail to Report In

(1)37 Tamper

Fire Alarms

(1)38 Near Alarm

(1)1A Fire Alarm

General Alarms

(1)11 Smoke

(1)4A General Alarm

(1)12 Combustion

(1)43 Exp. module failure

(1)13 Water Flow

(1)44 Sensor tamper

(1)14 Heat

(1)45 Module Tamper

(1)15 Pull Station

(1)4A Cross Zone Police Code

(1)16 Duct

24 Hour Non-Burglary

(1)17 Flame

(1)5A 24 Hour non-Burg

(1)18 Near Alarm

(1)51 Gas detected

Panic Alarms

(1)52 Refrigeration

(1)2A Panic

(1)53 Loss of Heat

(1)21 Duress

(1)54 Water Leakage

(1)22 Silent

(1)55 Foil Break

(1)23 Audible

(1)56 Day Trouble

Burglar Alarms

(1)57 Low bottled Gas level

(1)3A Burglary

(1)58 High Temp

(1)31 Perimeter

(1)59 Low Temp

(1)32 Interior

(1)61 Loss of Air Flow

(1)33 24 Hour

Zone Definition

SIA Auto Rep
Codes*

Zone Alm/Rest.

Delay, Instant, Interior, Delay
Stay/Away, Interior Stay/Away,
24-hr Burg.

BA-ZZ/BH-ZZ

24-hr Fire

FA-ZZ/FH-ZZ

24-hr Supervisory Buzzer

UA-ZZ/UH-ZZ

24-hr Sprinkler

SA-ZZ/SH-ZZ

24-hr Gas

GA-ZZ/GH-ZZ

24-hr Heat

KA-ZZ/KH-ZZ

24-hr Medical

MA-ZZ/MH-ZZ

24-hr Emergency (non-medical)

QA-ZZ/QH-ZZ

24-hr Waterflow

WA-ZZ/WH-ZZ

24-hr Freeze

ZA-ZZ/ZH-ZZ

24-hr Holdup

HA-ZZ/HH-ZZ

24-hr Panic

PA-ZZ/PH-ZZ

Latching 24-hr

BA-ZZ/BH-ZZ

* ZZ = zones 01-32

Summary of Contents for Envoy NT9010

































































Search results

Summary of Contents for Envoy NT9010

Reviews:

DSC Envoy NT9010, Installation Manual, Page: 58 / 64

Search results

Summary of Contents for Envoy NT9010

Reviews: