manualshive.com logo in svg

Dodge 2014 SRT Viper, Owner'S Manual

The Dodge 2014 SRT Viper Owner's Manual is a comprehensive guide that provides detailed instructions and information about the iconic sports car. This essential manual covers everything from maintenance schedules to advanced driving techniques. Download this manual for free from manualshive.com and unleash the full potential of your SRT Viper.

Share
Download
background image

INSTALLATION OF RADIO TRANSMITTING
EQUIPMENT

Special design considerations are incorporated into this
vehicle’s electronic system to provide immunity to radio
frequency signals. Mobile two-way radios and telephone
equipment must be installed properly by trained person-
nel. The following must be observed during installation.

The positive power connection should be made directly
to the battery and fused as close to the battery as possible.
The negative power connection should be made to body
sheet metal adjacent to the negative battery connection.
This connection should not be fused.

Antennas for two-way radios should be mounted on the
roof or the rear area of the vehicle. Care should be used
in mounting antennas with magnet bases. Magnets may
affect the accuracy or operation of the compass on
vehicles so equipped.

The antenna cable should be as short as practical and
routed away from the vehicle wiring when possible. Use
only fully shielded coaxial cable.

Carefully match the antenna and cable to the radio to
ensure a low Standing Wave Ratio (SWR).

Mobile radio equipment with output power greater than
normal may require special precautions.

All installations should be checked for possible interfer-
ence between the communications equipment and the
vehicle’s electronic systems.

Summary of Contents for 2014 SRT Viper

















































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 SRT Viper

Kia 2016 Cadenza Owner'S Manual preview
2016 Cadenza
Brand: Kia Pages: 419
EUFAB 12015 Manual preview
12015
Brand: EUFAB Pages: 12
Kolpin Outdoors 25-1080 Assembly & Owners Manual preview
25-1080
Brand: Kolpin Outdoors Pages: 6
Schartec CR 4 Manual preview
CR 4
Brand: Schartec Pages: 2
Mini COOPER Owner'S Manual preview
COOPER
Brand: Mini Pages: 20
Right Weigh 221-SK Installation Manual preview
221-SK
Brand: Right Weigh Pages: 16
Horn Tools HJIMRR02FIT Mounting Instructions preview
HJIMRR02FIT
Brand: Horn Tools Pages: 12
HAKR TRIP 3 Instructions For Use Manual preview
TRIP 3
Brand: HAKR Pages: 9
QA1 GS501 Installation Instructions preview
GS501
Brand: QA1 Pages: 3
Ranger design 1525-NSX Quick Start Manual preview
1525-NSX
Brand: Ranger design Pages: 22
Husky 31564 Assembly, Installation, Operation And Maintenance Instructions preview
31564
Brand: Husky Pages: 8
Ford 2003 Ranger Quick Reference Manual preview
2003 Ranger
Brand: Ford Pages: 2
Toyota 4Runner 2020 Owner'S Manual preview
4Runner 2020
Brand: Toyota Pages: 596
Toyota 2009 Tacoma Quick Reference Manual preview
2009 Tacoma
Brand: Toyota Pages: 22
Mazda MVG 4507 F Installation Instruction preview
MVG 4507 F
Brand: Mazda Pages: 38
Chevrolet 2003 Suburban Owner'S Manual preview
2003 Suburban
Brand: Chevrolet Pages: 516
Honda 2011 CR-Z Owner'S Manual preview
2011 CR-Z
Brand: Honda Pages: 332
FORM FIT HD 5H 08 Manual preview
HD 5H 08
Brand: FORM FIT Pages: 4

Brands by name

Popular brands

Load more brands