Dodge 2014 SRT Viper Owner'S Manual Download Page 208

Page: 208 / 400

Get Started

1. Visit UconnectPhone.com to check mobile device and

feature compatibility and to find phone pairing in-
structions.

2. Reduce background noise. Wind and passenger con-

versations are examples of noise that may impact
recognition.

3. Speak clearly at a normal pace and volume while

facing straight ahead. The microphone is positioned
on the rearview mirror and aimed at the driver.

4. Each time you give a Voice Command, you must first

push either the VR or Phone button, wait until

after

the beep, then say your Voice Command.

5. You can interrupt the help message or system prompts

by pushing the VR or Phone button and saying a Voice
Command from current category.

Two buttons are all you need to control your Uconnect®
system with your voice.

Basic Voice Commands

The basic Voice Commands below can be given at any
point while using your Uconnect® system.

Push the VR button

. After the beep, say:

•

Cancel

to stop a current voice session

•

Help

to hear a list of suggested Voice Commands

•

Repeat

to listen to the system prompts again

Notice the visual cues that inform you of your voice
recognition system’s status. Cues appear on the touch-
screen.

206

UNDERSTANDING YOUR INSTRUMENT PANEL

Summary of Contents for 2014 SRT Viper

















































































































































































































































































































































































































Search results

Summary of Contents for 2014 SRT Viper

Reviews:

Related manuals for 2014 SRT Viper

Brands by name

Popular brands

Dodge 2014 SRT Viper, Owner'S Manual

Search results

Summary of Contents for 2014 SRT Viper

Reviews:

Related manuals for 2014 SRT Viper

Brands by name

Popular brands