Dodge 2014 SRT Viper Owner'S Manual Download Page 115 | Manualshive

Page: 115 / 400

background image

•

The pedals cannot be adjusted when the vehicle is in
REVERSE or when the Electronic Speed Control Sys-
tem is on. The following messages will be displayed in
the Driver Information Display (DID) if the pedals are
attempted to be adjusted when the system is locked
out (“Adjustable Pedal Disabled — Cruise Control
Engaged” or “Adjustable Pedal Disabled — Vehicle In
Reverse”).

NOTE:

•

Always adjust the pedals to a position that allows full
pedal travel.

•

Further small adjustments may be necessary to find
the best possible seat/pedal position.

CAUTION!

Do not place any article under the adjustable pedals
or impede its ability to move as it may cause damage
to the pedal controls. Pedal travel may become lim-
ited if movement is stopped by an obstruction in the
adjustable pedal’s path.

WARNING!

Do not adjust the pedals while the vehicle is moving.
You could lose control and have an accident. Always
adjust the pedals while the vehicle is parked.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

113

«
...
113
114
115
116
117
...
»

Summary of Contents for 2014 SRT Viper

















































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 SRT Viper

Brand: Acdeos Pages: 38

Brand: Federal Signal Corporation Pages: 8

Brand: Federal Signal Corporation Pages: 8

Brand: Jackco Pages: 11

Brand: Ultra-tow Pages: 14

Brand: Mercedes-Benz Pages: 121

Brand: Menabo Pages: 8

Brand: Camtree Pages: 5

CARPOWER CAP-12XHQ

Brand: Monacor Pages: 5

Grand Cherokee WK2

Brand: Jeep Pages: 338

10-8002-C11670C

Brand: Saleen Pages: 17

Brand: Nav TV Pages: 2

Brand: Omix-Ada Pages: 6

Brand: KEKO Pages: 3

Brand: Movon Pages: 43

Brand: Skoda Pages: 324

Brand: PEUGEOT Pages: 232

2010 Accord Coupe

Brand: Honda Pages: 410

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands