Dodge 2014 SRT Viper Owner'S Manual Download Page 215

Page: 215 / 400

Roadside Assistance Call

Wi-Fi Hotspot***

**If vehicle is equipped.

***Extra charges apply.

Register (8.4AN)

1. Press the

SRT & Apps

button on the bottom of the

8.4-inch touchscreen.

2. If a pop-up message appears, press

Register

or go to

the

Favorite Apps

menu and press

Uconnect® Regis-

tration

3. Read through the registration instructions. Enter and

confirm your personal email address. Then press

Send

4. Check your personal inbox for an email from

Uconnect® Access.

5. Click on the link inside the email within

72 hours

and

complete the easy online registration process to create
a personal Mopar® Owner Connect account linked to
your vehicle.

Uconnect® Registration 8.4AN

UNDERSTANDING YOUR INSTRUMENT PANEL

213

Summary of Contents for 2014 SRT Viper

















































































































































































































































































































































































































Search results

Summary of Contents for 2014 SRT Viper

Reviews:

Related manuals for 2014 SRT Viper

Brands by name

Popular brands

Dodge 2014 SRT Viper, Owner'S Manual

Search results

Summary of Contents for 2014 SRT Viper

Reviews:

Related manuals for 2014 SRT Viper

Brands by name

Popular brands