Dodge 2014 SRT Viper Owner'S Manual Download Page 147 | Manualshive

Page: 147 / 400

background image

NOTE:

Leaving the hazard flashers on for extended

periods will wear down the battery.

5. Electronic

Stability

Control

(ESC)

Activation/

Malfunction Indicator Light — If Equipped

The “ESC Activation/Malfunction Indicator
Light” in the instrument cluster will come on
when the ignition is cycled to the ON/RUN
position. It should go out with the engine

running. If the “ESC Activation/Malfunction Indicator
Light” comes on continuously with the engine running, a
malfunction has been detected in the ESC system. If this
light remains on after several ignition cycles, and the
vehicle has been driven several miles (kilometers) at
speeds greater than 30 mph (48 km/h), see your autho-
rized dealer as soon as possible to have the problem
diagnosed and corrected.

NOTE:

•

The “ESC Off Indicator Light” and the “ESC
Activation/Malfunction Indicator Light” come on
momentarily each time the ignition is cycled to
ON/RUN.

•

Each time the ignition is cycled to ON/RUN, the
ESC system will be ON, even if it was turned off
previously.

•

The ESC system will make buzzing or clicking
sounds when it is active. This is normal; the sounds
will stop when ESC becomes inactive following the
maneuver that caused the ESC activation.

6. Driver Information Display (DID) Menu Set (Select-
able ICONS)

The DID displays are located in the center portion of the
cluster and consists of eight section:

•

Speedometer (Digital or Analog) (km/h or mph)

4

UNDERSTANDING YOUR INSTRUMENT PANEL

145

«
...
145
146
147
148
149
...
»

Summary of Contents for 2014 SRT Viper

















































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 SRT Viper

Brand: Laser Pages: 8

Brand: Kathrein Pages: 7

Brand: TATA Motors Pages: 161

Brand: TAUBENREUTHER Pages: 11

Brand: Yakima Pages: 15

Brand: Vauxhall Pages: 2

Wireless Handsfree Car Kit

Brand: Wagan Pages: 20

Brand: Mazda Pages: 13

Quattroporte Automatic

Brand: Maserati Pages: 272

Brand: femkes Pages: 7

PRIME DESIGN VRR-E-PM21

Brand: Safe Fleet Pages: 12

Brand: tams elektronik Pages: 44

Brand: Toyota Pages: 636

Brand: Mercedes-Benz Pages: 39

2013 GMC Savana

Brand: GMC Pages: 398

Brand: Oldsmobile Pages: 354

Brand: Oldsmobile Pages: 248

Ridesmart KMA-610

Brand: KlipXtreme Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands