Dodge 2014 SRT Viper Owner'S Manual Download Page 338 | Manualshive

Page: 338 / 400

background image

manufacturer’s recommended brake fluid. Refer to “Flu-
ids, Lubricants, and Genuine Parts” in “Maintaining Your
Vehicle” for further information.

Rear Axle

Axle Lubricant Level Check

Check the exterior of the axle for evidence of gear oil
leakage every 12 months or 6,000 miles (10 000 km). This
check should be made with the vehicle level and on the
ground or raised on an axle and wheel type hoist. The
axle lubricant level should be between the bottom of the
filler plug and a point approximately 3/8 inch (9.5 mm)
below the filler plug. If adding axle lubricant, use only
the manufacturer’s recommended axle lubricant. Refer to
“Fluids, Lubricants, and Genuine Parts” in “Maintaining
Your Vehicle” for further information.

CAUTION!

Using axle fluid other than the manufactured recom-
mended fluid may cause a shudder/noise issue. refer
to “Fluids Lubes and Genuine Parts” in “ Maintain-
ing Your Vehicle” for further information.

Change Axle Lubricant

Refer to “Maintenance Schedule” for the proper mainte-
nance intervals. Change the lubricant immediately if
contaminated with water. See your authorized dealer for
service.

Appearance Care And Protection From Corrosion

Protection Of Body And Paint From Corrosion

Vehicle body care requirements vary according to geo-
graphic locations and usage. Chemicals that make roads
passable in snow and ice, and chemicals that are sprayed
on trees and road surfaces during other seasons, are

336

MAINTAINING YOUR VEHICLE

«
...
336
337
338
339
340
...
»

Summary of Contents for 2014 SRT Viper

















































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 SRT Viper

Brand: Happy Orange Pages: 2

Brand: Vauxhall Pages: 2

Brand: Warrior Products Pages: 4

Brand: Sirius Satellite Radio Pages: 8

Brand: Yakima Pages: 21

Carpower CAP-20

Brand: Monacor Pages: 2

Brand: Meta System Pages: 16

Brand: Atera Pages: 3

Brand: Black Horse Pages: 5

Brand: Calix group Pages: 4

Brand: Toyota Pages: 779

Brand: Brink Pages: 21

Brand: Rhino-Rack Pages: 2

Brand: Curt Group Pages: 2

Brand: Hama Pages: 39

Brand: Istar Pages: 6

Brand: Yakima Pages: 10

Brand: Kargo Master Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands