manualshive.com logo in svg

Dodge 2014 SRT Viper, Owner'S Manual

The Dodge 2014 SRT Viper Owner's Manual is a comprehensive guide that provides detailed instructions and information about the iconic sports car. This essential manual covers everything from maintenance schedules to advanced driving techniques. Download this manual for free from manualshive.com and unleash the full potential of your SRT Viper.

Share
Download
background image

If Engine Fails To Start

CAUTION!

To prevent damage to the starter, do not crank the
engine for more than 15 seconds at a time. Wait 10 to
15 seconds before trying again.

WARNING!

•

Never pour fuel or other flammable liquids into
the throttle body air inlet opening in an attempt to
start the vehicle. This could result in a flash fire
causing serious personal injury.

(Continued)

WARNING!

(Continued)

•

Do not attempt to push or tow your vehicle to get it
started. Unburned fuel could enter the catalytic
converter and once the engine has started, ignite
and damage the converter and vehicle. If the ve-
hicle has a discharged battery, booster cables may
be used to obtain a start from a booster battery or
the battery in another vehicle. This type of start can
be dangerous if done improperly, so follow this
procedure carefully. Refer to “Jump Starting” in
“What To Do In Emergencies” for further informa-
tion.

If the engine is flooded, it may start to run, but not have
enough power to continue running when the ENGINE
START button is released. If this occurs, continue crank-
ing up to 15 seconds with the accelerator pedal pushed

224

STARTING AND OPERATING

Summary of Contents for 2014 SRT Viper

















































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 SRT Viper

Calira 811 Manual preview
811
Brand: Calira Pages: 14
Camcar 40104 Mounting Instructions preview
40104
Brand: Camcar Pages: 6
Toyota 2012 Rav4 Owner'S Manual preview
2012 Rav4
Brand: Toyota Pages: 529
iDataLink ADS-ALCA Install Manuals preview
ADS-ALCA
Brand: iDataLink Pages: 30
EUFAB 12015 Manual preview
12015
Brand: EUFAB Pages: 12
B-Speech Pago INBTHF020 User Manual preview
Pago INBTHF020
Brand: B-Speech Pages: 24
Actia TGU-R ACCESS User Manual preview
TGU-R ACCESS
Brand: Actia Pages: 37
Yakima K674 Instructions Manual preview
K674
Brand: Yakima Pages: 13
Menabo 000081000000, Fitting Instructions Manual preview
000081000000,
Brand: Menabo Pages: 11
VDO DLD Wide Range II Installation Instructions Manual preview
DLD Wide Range II
Brand: VDO Pages: 84
Wagan TravelCharge Companion GO-Plus User Manual preview
TravelCharge Companion GO-Plus
Brand: Wagan Pages: 3
I.D. Systems Vehicle Asset Communicator User Manual preview
Vehicle Asset Communicator
Brand: I.D. Systems Pages: 41
ULTIMATE SPEED 279619 Instructions For Use And Safety Manuallines preview
279619
Brand: ULTIMATE SPEED Pages: 40
Black Horse Off Road TO20 Installation Instructions Manual preview
TO20
Brand: Black Horse Off Road Pages: 7
Honda 1991 Civic Online Reference Owner'S Manual preview
1991 Civic
Brand: Honda Pages: 124
S&B Filters 75-5053 Installation Instructions preview
75-5053
Brand: S&B Filters Pages: 4
Mazda 2016 CX3 Service Information preview
2016 CX3
Brand: Mazda Pages: 3
Huf HUF8432MS Technical Description And User Manual preview
HUF8432MS
Brand: Huf Pages: 6

Brands by name

Popular brands

Load more brands