Dodge 2014 SRT Viper Owner'S Manual Download Page 306

Page: 306 / 400

NOTE:

The battery is located underneath an access

panel inside the rear compartment on the left side of the
vehicle. A remote battery terminal is located in the engine
compartment for jump-starting.

Connecting The Jumper Cables

1. Wear eye protection and remove any metal jewelry

such as watchbands or bracelets that might make an
inadvertent electrical contact.

2. When boost is provided by a battery in another

vehicle, park that vehicle within booster cable reach,
but without allowing the vehicles to touch one an-
other.

3. Set the parking brake, place the transmission in NEU-

TRAL, and turn the ignition OFF on both vehicles.

4. Turn off the heater, radio, and all unnecessary electri-

cal loads.

5. Remove the plastic fuse cover to gain access to the

remote jump-start positive

(+)

post in the engine

compartment. Refer to the following illustration for
remote jump-starting connections.

Battery Location

304

WHAT TO DO IN EMERGENCIES

Summary of Contents for 2014 SRT Viper

















































































































































































































































































































































































































Search results

Summary of Contents for 2014 SRT Viper

Reviews:

Related manuals for 2014 SRT Viper

Brands by name

Popular brands

Dodge 2014 SRT Viper, Owner'S Manual

Search results

Summary of Contents for 2014 SRT Viper

Reviews:

Related manuals for 2014 SRT Viper

Brands by name

Popular brands