Dodge 2014 SRT Viper Owner'S Manual Download Page 294

Page: 294 / 400

Inspect the wheel mounting surface prior to mounting
the tire and remove any corrosion or loose particles.

Tighten the lug nuts/bolts in a star pattern until each
nut/bolt has been tightened twice.

After 25 miles (40 km) check the lug nut/bolt torque to be
sure that all the lug nuts/bolts are properly seated
against the wheel.

Wheel Mounting Surface

Torque Patterns

292

WHAT TO DO IN EMERGENCIES

Summary of Contents for 2014 SRT Viper

















































































































































































































































































































































































































Search results

Summary of Contents for 2014 SRT Viper

Reviews:

Related manuals for 2014 SRT Viper

Brands by name

Popular brands

Dodge 2014 SRT Viper, Owner'S Manual

Search results

Summary of Contents for 2014 SRT Viper

Reviews:

Related manuals for 2014 SRT Viper

Brands by name

Popular brands