Dodge 2014 SRT Viper Owner'S Manual Download Page 172 | Manualshive

Page: 172 / 400

background image

Trip B — If Equipped

Push and release Up or Down arrow button
until the Trip B icon is highlighted in the DID.
The Trip B information will display the
following:

•

Distance

•

Average Speed

•

Elapsed Time

Hold the RIGHT arrow button to reset all the informa-
tion.

Audio

Push and release the UP or DOWN arrow
button until the Audio display icon is high-
lighted in the DID. Push and release the RIGHT
arrow button to display the active source.

Stored Messages

Push and release the UP or DOWN arrow
button until the Messages Menu item is high-
lighted in the DID. This feature shows the
number of stored warning messages. Pushing

the RIGHT arrow button will allow you to see what the
stored messages are.

170

UNDERSTANDING YOUR INSTRUMENT PANEL

«
...
170
171
172
173
174
...
»

Summary of Contents for 2014 SRT Viper

















































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 SRT Viper

Brand: N-Com Pages: 28

Brand: AAMP of America Pages: 6

MARTEN-FREE CAR

Brand: Gardigo Pages: 36

Brand: GARO Pages: 23

LS4 Wallmounted

Brand: GARO Pages: 15

Brand: Roav Pages: 10

Brand: Waeco Pages: 172

Brand: VBG Pages: 16

Brand: Toro Pages: 24

Brand: Parkeon Pages: 43

RGBW Rock Lights

Brand: Lit Lightz Pages: 3

Brand: Ferve Pages: 28

Brand: Honda Pages: 253

Brand: Toyota Pages: 11

Brand: Aston Martin Pages: 415

Brand: Pet Gear Pages: 4

IGNIS 2022 Series

Brand: Suzuki Pages: 570

Brand: Mitsubishi Pages: 57

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands