Dodge 2014 SRT Viper Owner'S Manual Download Page 133 | Manualshive

Page: 133 / 400

background image

WARNING!

To avoid serious injury or death:

•

Only devices designed for use in this type of outlet
should be inserted into any 12 Volt outlet.

•

Do not touch with wet hands.

•

Close the lid when not in use and while driving the
vehicle.

•

If this outlet is mishandled, it may cause an electric
shock and failure.

CAUTION!

•

Many accessories that can be plugged in draw
power from the vehicle’s battery, even when not in
use (i.e., cellular phones, etc.). Eventually, if
plugged in long enough, the vehicle’s battery will
discharge sufficiently to degrade battery life and/or
prevent the engine from starting.

•

Accessories that draw higher power (i.e., coolers,
vacuum cleaners, lights, etc.) will degrade the bat-
tery even more quickly. Only use these intermit-
tently and with greater caution.

•

After the use of high power draw accessories, or
long periods of the vehicle not being started (with
accessories still plugged in), the vehicle must be
driven a sufficient length of time to allow the
generator to recharge the vehicle’s battery.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

131

«
...
131
132
133
134
135
...
»

Summary of Contents for 2014 SRT Viper

















































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 SRT Viper

Brand: Toyota Pages: 52

Brand: Inbay Pages: 20

Brand: Kuda Pages: 3

Brand: RAM Pages: 616

Brand: Nav TV Pages: 9

Brand: Honda Pages: 81

adaptiv mini ADVM-BM1

Brand: Connects2 Pages: 4

Brand: Porsche Pages: 313

Brand: CTEK Pages: 84

Brand: MAcarbon Pages: 3

Brand: Ford Pages: 40

Sprinter Bed System DIY

Brand: FVC Pages: 8

Turbocharger 15012

Brand: Edelbrock Pages: 1

Yukon XL Denali 2015

Brand: GMC Pages: 439

DH-RB 05.02 Series

Brand: Dhollandia Pages: 65

Brand: STO N SHO Pages: 7

Brand: INNO Pages: 3

Brand: Yakima Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands