manualshive.com logo in svg

Dodge 2014 SRT Viper, Owner'S Manual

The Dodge 2014 SRT Viper Owner's Manual is a comprehensive guide that provides detailed instructions and information about the iconic sports car. This essential manual covers everything from maintenance schedules to advanced driving techniques. Download this manual for free from manualshive.com and unleash the full potential of your SRT Viper.

Share
Download
background image

cruise conditions (relatively steady speeds) will result in
increased fuel economy, and may be used as indicated.

MANUAL TRANSMISSION

RECOMMENDED SHIFT SPEEDS

1-4

4-5

5-6

mph

17

45

50

(km/h)

(27)

(72)

(80)

Higher upshift speeds may be used to obtain a desired
acceleration rate.

Skip Shift Indicator Light

There are times when you must shift the trans-
mission directly from first gear into fourth gear
instead of from first gear into second gear. This
is to help you get the best possible fuel

economy from your vehicle. This occurs when engine

coolant is higher than 107°F (42°C), and vehicle speed is
greater than 16 mph (26 km/h) but less than 18 mph
(29 km/h), and engine speed is less than 1,550 RPM, and
the transmission is in first gear, and the accelerator is at
20% throttle or less. The “Skip Shift Indicator Light”
located in the tachometer will illuminate during these
times.

When the “Skip Shift Indicator Light” illuminates, the
shift mechanism will only allow shifts from first gear to
fourth gear. After you shift the transmission into fourth
gear, you can press the clutch in and shift to another
forward gear.

Downshifting - Proper downshifting will improve fuel
economy and prolong engine life.

To maintain a safe speed and prolong brake life, down-
shift to maintain a safe speed when descending a steep
grade.

228

STARTING AND OPERATING

Summary of Contents for 2014 SRT Viper

















































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 SRT Viper

Quadratec Brute Strength 12057.0271 Installation Manual preview
Brute Strength 12057.0271
Brand: Quadratec Pages: 6
Jacobsen Cushman Turf Truckster Parts & Maintenance Manual preview
Cushman Turf Truckster
Brand: Jacobsen Pages: 210
Sirius Satellite Radio Streamer GTR Installation Manual preview
Streamer GTR
Brand: Sirius Satellite Radio Pages: 8
Calitop Calispace Ocean 80 Assembly Instructions preview
Calispace Ocean 80
Brand: Calitop Pages: 5
MULTILIFT ULTIMA S Installation Instructions Manual preview
ULTIMA S
Brand: MULTILIFT Pages: 62
Air Lift 88365 Installation Manual preview
88365
Brand: Air Lift Pages: 28
Dolphin DAS400 Owner'S Manual preview
DAS400
Brand: Dolphin Pages: 16
FALCON RIDGE Bobcat 3400 Instructions For Installation And Care preview
Bobcat 3400
Brand: FALCON RIDGE Pages: 4
Honda 2010 Accord Coupe Owner'S Manual preview
2010 Accord Coupe
Brand: Honda Pages: 410
VP Autoparts 419420 Installation preview
419420
Brand: VP Autoparts Pages: 2
HUSKY LINERS 47954 Installation Instructions preview
47954
Brand: HUSKY LINERS Pages: 4
iOttie HLCRIO138 Manual preview
HLCRIO138
Brand: iOttie Pages: 19
Menabo 171071 Fitting Instructions preview
171071
Brand: Menabo Pages: 4
Buick 1997 Park Avenue Manual preview
1997 Park Avenue
Brand: Buick Pages: 420
AL-KO 605 363 Operating Instructions Manual preview
605 363
Brand: AL-KO Pages: 88
HawksHead TRACK MASTER Instruction Manual preview
TRACK MASTER
Brand: HawksHead Pages: 10
Curt Manufacturing 12070 Installation Instructions preview
12070
Brand: Curt Manufacturing Pages: 5
Jeep GRAND CHEROKEE 4xe 2023 Owner'S Manual preview
GRAND CHEROKEE 4xe 2023
Brand: Jeep Pages: 440

Brands by name

Popular brands

Load more brands