Dodge 2014 SRT Viper Owner'S Manual Download Page 116 | Manualshive

Page: 116 / 400

background image

Adjustable Foot Rest

This feature allows the driver to adjust the foot rest
forward or backward and to rotate it upward or down-
ward to allow for greater driving comfort.

To adjust the pedal:

1. Adjust the seat and steering column to a comfortable

position.

2. Using a socket wrench, loosen the nut on the pedal.

3. Slide the pedal either forward or backward and rotate

it upward or downward as desired.

4. Tighten the nut, being careful not to over tighten it.

ELECTRONIC SPEED CONTROL

When engaged, the Electronic Speed Control takes over
accelerator operations at speeds greater than 25 mph
(40 km/h).

The Electronic Speed Control buttons are located on the
right side of the steering wheel.

Adjustable Foot Rest

114

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
114
115
116
117
118
...
»

Summary of Contents for 2014 SRT Viper

















































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 SRT Viper

Brand: Garmin Pages: 2

Brand: Chevrolet Pages: 356

Brand: Ford Pages: 272

Brand: Pontiac Pages: 376

Brand: Jeep Pages: 712

Brand: TrailFX Pages: 6

Brand: Yakima Pages: 19

UCI-11C NTV-KIT331

Brand: Nav TV Pages: 4

Brand: Safe Fleet Pages: 11

Brand: Camec Pages: 19

Brand: Chevrolet Pages: 376

Brand: Mazda Pages: 15

Brand: Condor Pages: 2

Brand: iArmor Pages: 4

2010 MX-5 Miata

Brand: Mazda Pages: 8

RAV-4 2015 Series

Brand: Toyota Pages: 50

Brand: TomTom Pages: 22

Brand: MiX Telematics Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands