Dodge 2014 SRT Viper Owner'S Manual Download Page 120 | Manualshive

Page: 120 / 400

background image

Metric Speed (km/h)

•

Pushing the SET (-) button once will result in a 1 km/h
decrease in set speed. Each subsequent tap of the
button results in a decrease of 1 km/h.

•

If the button is continually pushed, the set speed will
continue to decrease until the button is released, then
the new set speed will be established.

To Accelerate For Passing

Push the accelerator as you would normally. When the
pedal is released, the vehicle will return to the set speed.

NOTE:

If the accelerated speed goes above 10 mph

(16 km/h) of the set speed, the Electronic Speed Control
will deactivate.

PARKVIEW® REAR BACK UP CAMERA — IF
EQUIPPED

Your vehicle may be equipped with the ParkView® Rear
Back Up Camera that allows you to see an on-screen
image of the rear surroundings of your vehicle whenever
the shift lever/gear selector is put into REVERSE. The
ParkView® camera is located on the rear of the vehicle
above the rear license plate. The image will be displayed
in the touchscreen display along with a caution note to
“check entire surroundings” across the top of the screen.
After five seconds this note will disappear.

NOTE:

The ParkView® Rear Back Up Camera has pro-

grammable modes of operation that may be selected
through the Uconnect® System. Refer to “Uconnect®
Settings” in “Understanding Your Instrument Panel” for
further information.

If your vehicle is equipped with the Camera Delay
feature and it is turned ON, the rear camera image will be

118

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
118
119
120
121
122
...
»

Summary of Contents for 2014 SRT Viper

















































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 SRT Viper

Brand: Kargo Master Pages: 5

Brand: Aries Pages: 3

Brand: Chevrolet Pages: 344

Brand: Prorack Pages: 15

Brand: Easee Pages: 12

Brand: Hella Pages: 21

BASIC TLL171231

Brand: Tellur Pages: 5

Brand: H&S Pages: 32

Brand: Jaeger Pages: 13

OPTIA hybrid 2020

Brand: Kia Pages: 54

Brand: Volkswagen Zubehör Pages: 133

Brand: Ford Pages: 10

Brand: Fiat Pages: 204

Brand: Camcar Pages: 6

330e Touring xDrive G21 2021

Brand: BMW Pages: 102

EXPLORER A90095

Brand: SportRack Pages: 6

Brand: Lippert Components Pages: 14

Brand: Thule Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands