Dodge 2014 SRT Viper Owner'S Manual Download Page 96 | Manualshive

Page: 96 / 400

background image

SEATS

Seats are a part of the Occupant Restraint System of the
vehicle.

WARNING!

•

It is dangerous to ride in a cargo area, inside or
outside of a vehicle. In a collision, people riding in
these areas are more likely to be seriously injured
or killed.

•

Do not allow people to ride in any area of your
vehicle that is not equipped with seats and seat
belts. In a collision, people riding in these areas are
more likely to be seriously injured or killed.

•

Be sure everyone in your vehicle is in a seat and
using a seat belt properly.

Manual Seats

Forward And Rearward Adjustment

The adjusting bar is at the front of the seat, near the floor.
Pull the bar upward to move the seat forward or rear-
ward. Release the bar once the seat is in the desired

Seat Adjustment Bar

94

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
94
95
96
97
98
...
»

Summary of Contents for 2014 SRT Viper

















































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 SRT Viper

Brand: GMC Pages: 140

Brand: Feniex Pages: 6

PRIME DESIGN VCR 326

Brand: Safe Fleet Pages: 16

Prime Design VBC PC11

Brand: Safe Fleet Pages: 8

Prime Design AR1418

Brand: Safe Fleet Pages: 4

Indigo MANZA QUADRAJET 90

Brand: TATA Motors Pages: 10

Brand: Chevrolet Pages: 2

Brand: TATA Motors Pages: 236

Calispace Ocean 80

Brand: Calitop Pages: 5

Brand: Baja Designs Pages: 5

Brand: E&G Classics Pages: 3

Brand: Thule Pages: 12

Brand: POOL-LINE Pages: 2

K40 Platinum360

Brand: K40 ELECTRONICS Pages: 11

Brand: Toyota Pages: 36

Brand: Autoplugin Pages: 8

Brand: Sintrones Pages: 55

Brand: Metra Electronics Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands