Dodge 2014 SRT Viper Owner'S Manual Download Page 13 | Manualshive

Page: 13 / 400

background image

A WORD ABOUT YOUR KEYS

Your vehicle uses a keyless ignition system. This system
consists of a Key Fob with Remote Keyless Entry (RKE)
transmitter and a Keyless Ignition Node (KIN).

Keyless Enter-N-Go™ Feature

This vehicle is equipped with the Keyless Enter-N-Go™
feature, (refer to

⬙

Keyless Enter-N-Go

⬙

in

⬙

Things To Know

Before Starting Your Vehicle

⬙

for further information).

Keyless Ignition Node (KIN)

This feature allows the driver to operate the ignition with
the push of a button, as long as the Remote Keyless Entry
(RKE) transmitter is in the passenger compartment.

The Keyless Ignition Node (KIN) has four operating
positions; three of which are labeled and will illuminate
when in position. The three positions are OFF, ACC, and
ON/RUN. The fourth position is START, during start
RUN will illuminate.

NOTE:

In case the ignition does not change with the

push of a button, the RKE transmitter (Key Fob) may
have a low or dead battery.

Keyless Ignition Node (KIN)

1 — OFF

2 — ACC (ACCESSORY)

3 — ON/RUN

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

11

«
...
11
12
13
14
15
...
»

Summary of Contents for 2014 SRT Viper

















































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 SRT Viper

Brand: Lancia Pages: 276

Brand: T-Tech Pages: 38

V2 SUPERCHARGER

Brand: Tesla Pages: 9

Sprinter Bed System Adventure Wagon Kit

Brand: FVC Pages: 8

Brand: FORM FIT Pages: 2

Edge Flush Rail

Brand: Thule Pages: 12

Brand: GMC Pages: 499

Brand: Kia Pages: 290

Brand: Mercedes-Benz Pages: 368

Brand: Honda Pages: 85

Brand: r.LiNK Pages: 21

Interlock 700 Series

Brand: Scania Pages: 82

Brand: Oldsmobile Pages: 358

Brand: Renault Pages: 11

Brand: Metra Electronics Pages: 12

Brand: Honda Pages: 326

80-485-142401-RT

Brand: Classic Accessories Pages: 14

Brand: Fortin Electronic Systems Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands