Dodge 2014 SRT Viper Owner'S Manual Download Page 110 | Manualshive

Page: 110 / 400

background image

Interior Light Defeat (OFF)

Rotate the dimmer control to the extreme bottom OFF
position. The interior lights will remain off when the
doors are open.

Parade Mode (Daytime Brightness Feature)

Rotate the instrument panel dimmer control upward to
the first detent. This feature brightens all text displays
such as the odometer, Driver Information Display (DID),
and radio when the position lights or headlights are on.

WINDSHIELD WIPERS AND WASHERS

The multifunction lever operates the windshield wipers
and washer when the ignition is placed in the ON/RUN
or ACC position. The multifunction lever is located on
the left side of the steering column.

Intermittent Wiper System

Use the intermittent wiper when weather conditions
make a single wiping cycle with a variable pause be-
tween cycles desirable. Rotate the end of the multifunc-
tion lever to the first detent position, and then turn the
end of the lever to select the desired delay interval. There

Windshield Wiper/Washer Control

108

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
108
109
110
111
112
...
»

Summary of Contents for 2014 SRT Viper

















































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 SRT Viper

Brand: Jeep Pages: 25

AUDI 4G HIGHEND

Brand: KAP Pages: 20

Brand: Front Runner Pages: 5

Brand: Daewoo Pages: 68

Brand: Hyundai Pages: 437

Brand: FORM FIT Pages: 2

Edge Flush Rail

Brand: Thule Pages: 12

Brand: Van Guard Pages: 3

Brand: Mazda Pages: 122

Brand: FALCON RIDGE Pages: 7

Brand: Volvo Pages: 30

Brand: Abrams Pages: 12

2010 Challenger SRT

Brand: Dodge Pages: 444

Brand: Prorack Pages: 15

Brand: Honda Pages: 268

Brand: Lincoln Pages: 586

Brand: Saab Pages: 288

Brand: Ford Pages: 51

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands