Dodge 2014 SRT Viper Owner'S Manual Download Page 337 | Manualshive

Page: 337 / 400

background image

brake fluid must be changed at the intervals specified in
the “Maintenance Schedule.” Refer to “Maintenance
Schedule” for further information. See your authorized
dealer for service.

Manual Transmission

Transmission Fluid Level Check

Check the fluid in the transmission when performing
other underbody services.

Check the fluid level by removing the fill plug located on
the left side of the transmission. The fluid level should be
approximately 1/4 in (6.4 mm) below the bottom of the
fill hole. Add fluid, if necessary, to maintain the proper
level. Refer to “Fluids, Lubricants, and Genuine Parts” in
“Maintaining Your Vehicle” for further information.

NOTE: DO NOT

overfill transmission, damage can

occur.

CAUTION!

Using a transmission fluid other than the manufac-
turer’s recommended fluid may cause deterioration
in transmission shift quality and/or damage to the
transmission. Refer to “Fluids, Lubricants, and
Genuine Parts” in this section for fluid specifica-
tions.

Change Transmission Fluid

Refer to “Maintenance Schedule” for the proper mainte-
nance intervals. If contaminated with water, change the
fluid immediately. See your authorized dealer for service.

Hydraulic Clutch

Master Cylinder – Clutch Fluid Level Check

The clutch hydraulic system is fed by a segregated
volume of fluid within the brake system master cylinder
reservoir. In the event of leakage or wear, use only the

7

MAINTAINING YOUR VEHICLE

335

«
...
335
336
337
338
339
...
»

Summary of Contents for 2014 SRT Viper

















































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 SRT Viper

Brand: Lancia Pages: 276

Brand: T-Tech Pages: 38

Brand: Subaru Pages: 34

Brand: Sirius Satellite Radio Pages: 8

Brand: Whispbar Pages: 15

Brand: SAN HIMA Pages: 7

Peterbilt SmartAir

Brand: Paccar Pages: 58

Brand: Mercedes-Benz Pages: 153

Parrot MKi + ParrotCK3100 range LOGAN

Brand: Parrot Pages: 10

DAF CHARGEMAX 90

Brand: Paccar Pages: 40

Brand: Hyundai Pages: 11

Brand: Black Horse Off Road Pages: 7

Giulietta 2.0 JTDM

Brand: Alfa Romeo Pages: 14

Telescoping Computer Base C-TCB-34

Brand: Havis-Shields Pages: 1

Brand: PEUGEOT Pages: 107

Brand: Arrista Pages: 2

Brand: Acura Pages: 19

Brand: Ford Pages: 325

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands