Dodge 2014 SRT Viper Owner'S Manual Download Page 15 | Manualshive

Page: 15 / 400

background image

Ignition Or Accessory On Message

Opening the driver’s door when the ignition is in ACC or
ON (engine not running), a chime will sound to remind
you to cycle the ignition to OFF. In addition to the chime,
the ignition or accessory on message will display in the
cluster.

NOTE:

With the Uconnect® system, the power window

switches, radio and power outlets will remain active for
up to 10 minutes after the ignition is cycled to the OFF
position. Opening either front door will cancel this
feature. The time for this feature is programmable. Refer
to “Uconnect® Settings” in “Understanding Your Instru-
ment Panel” for further information.

WARNING!

•

When leaving the vehicle, always remove the Key
Fob from the vehicle and lock your vehicle.

•

Never leave children alone in a vehicle, or with
access to an unlocked vehicle.

(Continued)

Emergency Key Removal

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

13

«
...
13
14
15
16
17
...
»

Summary of Contents for 2014 SRT Viper

















































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 SRT Viper

Brand: Ranger design Pages: 6

Brand: CITROEN Pages: 52

Brand: AMP Research Pages: 12

Half Size Trunk Box Organizer C-TBO-CV

Brand: Havis-Shields Pages: 1

Brand: Volvo Pages: 8

Brand: Cadillac Pages: 34

Brand: Veigel Pages: 24

Brand: Cellular Line Pages: 25

Brand: Yakima Pages: 9

Brand: CrimeStopper Pages: 1

Brand: Qeedon Pages: 2

Brand: Jaeger Pages: 16

Brand: Lexus Pages: 82

Brand: Blue Ox Pages: 9

Brand: Mazda Pages: 605

Brand: Painless Performance Pages: 16

Brand: EUFAB Pages: 8

TRUCK 2500 2017

Brand: RAM Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands