Operation & Maintenance Manual
Section3-User Responsibility, Machine
Preparation, and Inspection
Dingli Machinery
3-9
lubrication; no evidence of loose bolts or looseness between bearing or structure. Swing
Motor and Worm Gear - No loose or missing hardware; no visible damage; evidence of
proper lubrication.
24)
Hydraulic Pump - No loose or missing parts, no evidence
25)
Battery - Proper electrolyte levels; cables tight, no visible damage or corrosion.
26)
Drive Motor, Brake, and Hub - No visible damage; no evidence of leakage.
27)
Wheel/Tire Assembly, Left Rear - Properly secured, no loose or missing lug nuts, no
visible damage.
28)
Rotator Cylinders - No visible damage; cylinder bolts secure; hydraulic hoses undamaged
and not leaking.
29)
Platform Gate - Latch, stop, and hinges in working condition and properly secured; no
loose or missing parts.
3.2.5 Daily Function Check
A functional check of all systems must be performed, once the walk-around inspection is
complete, in an area free of overhead and ground level obstructions. First, using the ground
controls, check all functions controlled by the ground controls. Next, using the platform
controls, check all functions controlled by the platform controls.
TO AVOID SERIOUS INJURY, DO NOT OPERATE MACHINE IF ANY
CONTROL LEVERS OR TOGGLE SWITCHES CONTROLLING
PLATFORM MOVEMENTS DO NOT RETURN TO THE OFF OR
NEUTRAL POSITION WHEN RELEASED.
TO AVOID A COLLISION AND INJURY IF PLATFORM DOES NOT
STOP WHEN A CONTROL SWITCH OR LEVER IS RELEASED,
REMOVE FOOT FROM FOOTSWITCH OR USE EMERGENCY STOP
TO STOP THE MACHINE.
IF THE MACHINE DOES NOT OPERATE PROPERLY, TURN OFF THE
MACHINE IMMEDIATELY! REPORT THE PROBLEM TO THE
PROPER MAINTENANCE PERSONNEL. DO NOT OPERATE THE
MACHINE UNTIL IT IS DECLARED SAFE FOR OPERATION.
NOTE:
When the boom is raised above horizontal, high drive speed is cut out
.
1)
Check boom horizontal limit switches to see that they are operable and not damaged.
Raise and lower Boom. Check for smooth operation. Check Boom Upright tilting for
proper synchronization. If the upright is tilted or the boom will not fully lower, refer to
the Boom Synchronizing Procedure in Section 5.8.
NOTE: Perform checks from ground controls first, then from platform controls
.
Summary of Contents for BA14J-AWD
