Datakom D-700 MK3 User Manual Download Page 164

Page: 164 / 218

D-700 MK3 User Manual Firmware V-16.8

- 164 -

The controller offers the automatic learning feature for adjusting synchronization & load sharing set-points
and PID coefficients.

The AUTO LEARNING makes the synchronization commissioning and fine adjusting a simple straightforward
operation.

In order to activate the AUTO LEARNING:

Please enter programming > synchronization parameters.

▪

Disable GOV control enable parameter.

▪

Gov Low Limit will be 0, Gov Gain will be 100 and Gov rest point will be 50.

▪

Disable AVR control enable parameter.

▪

AVR Low Limit will be 0, AVR Gain will be 100 and AVR rest point will be 50.

Start the generator manually.

▪

Adjust the required nominal frequency on the speed control unit using the speed pot.

▪

Adjust the required nominal voltage on the AVR unit using the voltage pot.

24. AUTO LEARNING

Summary of Contents for D-700 MK3



























































































































































































































Search results

Summary of Contents for D-700 MK3

Reviews:

Related manuals for D-700 MK3

Brands by name

Popular brands

Datakom D-700 MK3, User Manual

Search results

Summary of Contents for D-700 MK3

Reviews:

Related manuals for D-700 MK3

Brands by name

Popular brands