Danfoss PVED-CLS, User Manual, Page: 145 / 182

© Danfoss | August 2018 AQ00000211 |
145
ENGINEERING TOMORROW
Category SPN Signal Name Failure mode FMI Severity Possible root cause(s)
Software 520229 Soft error Soft error detected 31 - Condition exists Severe Internal failure
Software 520213 SPI Communication
Connection loss 11 - Unknown root-cause Severe Internal failure
SPI message queue full
2 - Data erratic, intermittent or
incorrect
Severe Internal failure
Software 1557 RAM test RAM-code test fails
12 - Bad intelligent device or
component
Severe Internal failure
Software 520579 EEPROM VPS data
Parameter value out of
range/Incorrect configuration
of EEPROM data
2 - Data erratic, intermittent or
incorrect
Severe
1. Parameter setting out of range
2. Incorrect sector CRC
Approval CRC failure 14 - Special instructions Severe
1. Incorrect Approval CRC
Software 520232 EEPROM Hydraulic config
Parameter value out of
range/Incorrect configuration
of EEPROM data
2 - Data erratic, intermittent or
incorrect
Severe
1. Parameter setting out of range
2. Incorrect sector CRC
Approval CRC failure 14 - Special instructions Severe
1. Incorrect Approval CRC
Software 520233 EEPROM SEHS FDA
Parameter value out of
range/Incorrect configuration
of EEPROM data
2 - Data erratic, intermittent or
incorrect
Severe
1. Parameter setting out of range
2. Incorrect sector CRC
Approval CRC failure 14 - Special instructions Severe
1. Incorrect Approval CRC
Software 520234
EEPROM Valve calibration
data
Parameter value out of
range/Incorrect configuration
of EEPROM data
2 - Data erratic, intermittent or
incorrect
Severe
1. Parameter setting out of range
2. Incorrect sector CRC
Approval CRC failure 14 - Special instructions Severe
1. Incorrect Approval CRC
Software 520235
EEPROM CAN WAS
Calibration data
Parameter value out of
range/Incorrect configuration
of EEPROM data
2 - Data erratic, intermittent or
incorrect
Severe
1. Parameter setting out of range
2. Illegal parameter combinations – see section 17.4.4
3. Incorrect sector CRC
Approval CRC failure 14 - Special instructions Severe
1. Incorrect Approval CRC
Software 520236
EEPROM Analogue Sensor
Calibration data
Parameter value out of
range/Incorrect configuration
of EEPROM data
2 - Data erratic, intermittent or
incorrect
Severe
1. Parameter setting out of range
2. Illegal parameter combinations – see section 17.4.5
3. Incorrect sector CRC
Approval CRC failure 14 - Special instructions Severe
1. Incorrect Approval CRC
Software 520237 EEPROM Peripherals config
Parameter value out of
range/Incorrect configuration
of EEPROM data
2 - Data erratic, intermittent or
incorrect
Severe
1. Parameter setting out of range
2. Illegal parameter combinations – see section 17.4.6
3. Incorrect sector CRC
Approval CRC failure 14 - Special instructions Severe
1. Incorrect Approval CRC
Software 520238 EEPROM SEHS Protocol data
Parameter value out of
range/Incorrect configuration
of EEPROM data
2 - Data erratic, intermittent or
incorrect
Severe
1. Parameter setting out of range
2. Incorrect sector CRC
Approval CRC failure 14 - Special instructions Severe
1. Incorrect Approval CRC
Software 520239 EEPROM Internal monitoring
Parameter value out of
range/Incorrect configuration
of EEPROM data
2 - Data erratic, intermittent or
incorrect
Severe
1. Parameter setting out of range
2. Incorrect sector CRC
Approval CRC failure 14 - Special instructions Severe
1. Incorrect Approval CRC
Software 520241 EEPROM Vehicle geometry
Parameter value out of
range/Incorrect configuration
of EEPROM data
2 - Data erratic, intermittent or
incorrect
Severe
1. Parameter setting out of range
2. Incorrect sector CRC
Approval CRC failure 14 - Special instructions Severe
1. Incorrect Approval CRC
Software 520242 EEPROM GPS config
Parameter value out of
range/Incorrect configuration
of EEPROM data
2 - Data erratic, intermittent or
incorrect
Severe
1. Parameter setting out of range
2. Illegal parameter combinations – see section 12
3. Incorrect sector CRC
Approval CRC failure 14 - Special instructions Severe 1. Incorrect Approval CRC
Software 520243 EEPROM STW config
Parameter value out of
range/Incorrect configuration
of EEPROM data
2 - Data erratic, intermittent or
incorrect
Severe
1. Parameter setting out of range
2. Illegal parameter combinations – see section 10
3. Incorrect sector CRC
Approval CRC failure 14 - Special instructions Severe
1. Incorrect Approval CRC
Software 520244 EEPROM AUX config
Parameter value out of
range/Incorrect configuration
of EEPROM data
2 - Data erratic, intermittent or
incorrect
Severe
1. Parameter setting out of range
2. Illegal parameter combinations – see section 11
3. Incorrect sector CRC
Approval CRC failure 14 - Special instructions Severe
1. Incorrect Approval CRC
Software 520245
EEPROM Auto-Calibration
config sector
Parameter value out of
range/Incorrect configuration
of EEPROM data
2 - Data erratic, intermittent or
incorrect
Severe
1. Parameter setting out of range
2. Incorrect sector CRC
Approval CRC failure 14 - Special instructions Severe 1. Incorrect Approval CRC
Software 520246 Invalid sensor configuration Invalid sensor configuration 31 – Condition exists Severe If parameter settings are not done as per section 6.1.1
Software 299005 Software Initialization
Fault in software
configuration or initialization
process
11 - Unknown root-cause Severe Internal failure
Software 299004 Division by zero Division by zero 11 - Unknown root-cause Severe Internal failure
Software 628 Flash test Flash test failure
12 - Bad intelligent device or
component
Severe Internal failure
Software 299002 Variable truncation Variable truncation 11 - Unknown root-cause Severe Internal failure
Software 299001 I2C communication I2C communication failure
12 - Bad intelligent device or
component
Severe Internal failure